すべてのメッセージ

Q: What is the difference between CS-L2 and CS-L2+ model?

尋ねた AntonelloGr に 2021-10-22 12:41:14

sharptrack2 Not sure... haven't seen a "+" model. Could be an artifact of HTML translation in your browser.

2021-10-23 01:01:56 役に立つ (0)
提出
回答 (0)

sharptrack2 The light illuminates for about 30 seconds, but any additional movement will turn it back on immediately, or movement while it is on, will keep it on.

2021-10-12 04:36:22 役に立つ (0)
提出
回答 (4)

Q: It fits CR-5 PRO H?

尋ねた BrunoVinicius に 2021-10-04 11:57:59

sharptrack2 Yes, these are universal Creality nozzles and fit almost all of Creality's printers.

2021-10-04 11:17:16 役に立つ (0)
提出
回答 (2)

Q: would it fit Geeetech A20T?

尋ねた Thomas Luxton に 2020-11-17 04:28:34

sharptrack2 Notsure, have to check the plate hardware to see if the threads match... it's a pretty basic arrangement and as long as the threads match and you have room for the finger wheel, it should work.

2021-09-27 10:53:34 役に立つ (0)
提出
回答 (2)

sharptrack2 @moebisCheck the alignment of the feed hole, it does comes extremely close to the Z axis screw rod. If it is being pushed to the side by the rod, it will scrape and bind in the extruder. There is a bit of play in the mounting screws so you do need to align things before tightening.

2021-09-27 10:52:03 役に立つ (0)
提出
回答 (2)

Q: the wire will be tall enough for ender 5 ?

尋ねた BG191818423 に 2021-09-20 06:53:51

sharptrack2 @BG191818423 - Should be. On my Ender 3, I had almost 12cm extra that had t be wrapped up out of the way.

2021-09-20 09:37:55 役に立つ (0)
提出
回答 (2)

Q: Fits on the new Creality Sermoon?

尋ねた frederiklamote に 2021-05-26 10:42:57

sharptrack2 Should fit, these are standard nozzles and the Sermoon description also says it uses standard size nozzles. Creality is pretty good about using standard parts on most of its printers to hp keep prices down and easy maintenance.

2021-09-10 12:46:05 役に立つ (0)
提出
回答 (2)

Q: Hello. What's the material, the case is made from?

尋ねた 1marko1982 に 2020-02-29 11:21:53

sharptrack2 ABS plastic I think. Pretty sturdy, I carry them in my backpack all the time, with cords, power supplies, small tools, etc. Minor scuff marks is all that have happened.

2021-09-10 12:41:19 役に立つ (0)
提出
回答 (4)

Q: Is it ok for CR-10 V3?please

尋ねた BG255515415 に 2021-09-05 10:24:19

sharptrack2 As in the description, this unit works on most of the popular Creality printers. You must check firmware versions and ensure you have the right hardware (driver board). The unit comes with 3 different mounting plates to match with the series printer you have.

2021-09-06 12:46:18 役に立つ (0)
提出
回答 (3)