招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Sulian2
08/01/2021
Servo appears well built having an aluminium centre casing with plastic end caps.
End caps have seals between them and centre casing to keep dirt out and a seal around the servo lead exit however there is no seal between the top casing and output shaft so dirt and moisture can get in.
Top casing was removed to check gears and they are all metal as described and look well manufactured, the only issue I could see was there was no grease in the output shaft bearing.
I have used some light silicone grease to lubricate the ball race and also put some around the output shaft to help stop dirt and moisture getting into the servo.
The included metal servo arm is good quality and of the double bolt clamp design which is very good.
Servo movement is 85° on standard settings (1000µs - 2000µs) so I think that you may be hard pushed to get 180° movement out of this servo.
I do not have an accurate test rig but I was seeing in excess 20kg/cm on my setup which is more than enough for my needs.
These appear to be very well built servos that should work well in service and taking into consideration the price they are excellent.
Servos were ordered, dispatched and received in 8 days from China to UK so excellent service all around.
2個DSSERVO DS3225 25KG 180度メタルギア高トルク防水デジタルサーボRC飛行機ロボット用
US$27.99
US$37.19
8
推奨事項
コメント (1)
Q: Will the system work with nitro / gas engines or will the additional vibration cause issues?
尋ねた JonSweet に 2020-06-04 10:32:14
BG368515354 Hi Jon as long as it is working and setup correctly And you have killed the power to a level that is appropriate then yes there is no reason why not. As long as it is installed in the correct plane (orentation). Please read and comprehend the instructions fully or seek advice. Please join a model club or go on-line to a forum for help. Are you asking or thinking that viberation is going to be a problem. If so then yes it is going to need a lot of suspension and or padding but it must be able to correct the flight problem ASAP. If you need a bit of help from a hands on person then your LMS is your best friend. Or go online to a Model Aircraft RC Forum...
2020-06-24 08:15:28 役に立つ (1)回答 (1)
尋ねた JonSweet に 2020-06-03 02:01:13
ridgeracer I agree. Also find a spot that is away from excess vibration and use thick enough double sided tape.
2020-06-04 11:51:36 役に立つ (2)回答 (4)
Jon Sweet
27/08/2021
Q: Is the Frsky RXSR receiver supplied with the BNF version ACCST or ACCESS?
尋ねた Sulian68 に 2021-07-03 04:46:11回答 (0)
Q: Will this be available in the UK warehouse?
尋ねた Sulian2 に 2021-02-13 04:09:28
BG111054512 Probably not, if so where are they ??
2021-04-30 07:56:37 役に立つ (2)回答 (2)
Sulian2@basetau The only thing I can suggest is to look at your antenna positions as this can have a very big effect on range.
Sulian2
17/01/2021
4
コメント (3)
Sulian2
17/01/2021
Sulian2
14/01/2021
Sulian2
17/01/2021
Sulian2
22/01/2021
Q: Would this connect with a Frsky Tyrannus X7?
尋ねた dvanzuydam に 2021-01-13 08:17:26
Sulian2 It depends which version of the X7, I believe the EU-LBT Version will require you to download and flash new firmware to your TX. The version for non eu should be OK. There are videos on YouTube on how to do this.
2021-01-15 07:45:15 役に立つ (0)回答 (1)
尋ねた Jonathanstahl83 に 2020-12-08 01:36:07
Sulian2 Yes it does work with standard servo connectors.
2021-01-15 07:40:14 役に立つ (1)回答 (5)
Q: is there an xt30 connected to the wires for the esc or do you have to solder it on yourself?
尋ねた melanconmarcus23 に 2021-01-02 08:41:41
Sulian2 There is an XT60 fitted to the ESC.
2021-01-15 07:38:54 役に立つ (0)回答 (1)
尋ねた mambo840 に 2019-08-13 04:29:33
Sulian2 Can be either by pressing the mode switch.
2020-12-19 04:27:25 役に立つ (0)回答 (1)
Q: Can you confirm the diameter of the propeller shaft please
尋ねた JonSweet に 2020-11-19 02:31:08
Partocracy Hello, we have sent the question to the supplier, will get back to you soon.
2020-12-04 04:20:52 役に立つ (0)回答 (1)
Q: Does the landing gear come with the kit option?
尋ねた JonSweet に 2020-11-10 01:16:18
Scuttle_butt yes.
2020-12-03 03:39:05 役に立つ (1)回答 (1)
Q: Could you let me know if this will this be available in a European warehouse soon? Thanks
尋ねた JonSweet に 2020-11-22 03:41:31
Yanny it will be available in CZ warehouse soon.
2020-12-01 03:45:41 役に立つ (4)回答 (1)
Jon Sweet
10/02/2020
