招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
msnowden
08/02/2020
Kit arrived in one month about 22 business days. It probably would have been earlier but Chinese New Year delayed it a few days. Although the box was dented and had two puncture holes, the kit was in good shape.
Balsa and ply planks have good quality and are laser cut. Only one plank required extra attention. Each piece is labeled, but not actually in the piece. What looked on models in the ads to be an aluminum tube in the wing was replaced with a carbon fiber tube into which two carbon fiber tubes fit. This helps add strength to the wing. However, the fit is so tight it meant the wing had to be permanently joined in the middle. I actually had to hammer the right wing’s rod into the larger joiner tube.
Building time is at least 30-40 hours. I did the set-up, parts marking, and built the wing and elevator in 12 hours.
A build log is in development.
DWウィンググリフィン1550mm翼幅バルサウッドRC飛行機キット
US$58.90
US$75.59
0
推奨事項
コメント (1)
尋ねた lloydertel に 2020-06-21 05:55:22
msnowden Not this one. Check ESC’s for RC boats.
2020-06-21 06:03:34 役に立つ (0)回答 (2)
Q: can you recommend a suitable speed controller for this motor?
尋ねた Tim に 2018-07-25 07:05:12
msnowden Brusheless ESC 30A Speed Control 2S 3S T-Plug JST for 2212 Brushless Motor KT SU27 RC Airplane FPV Racing Drone RC Car Boat
2020-02-11 08:10:23 役に立つ (1)回答 (2)
Q: is this the same prop that will fit the Volantex Phoenix?
尋ねた SWB に 2018-11-12 02:15:28
msnowden 3.17
2020-02-11 08:08:00 役に立つ (4)回答 (4)
尋ねた Jag に 2020-01-27 03:45:12
msnowden ESC’s do not need extra programming. The onboard receiver controls the inputs.
2020-01-27 06:47:53 役に立つ (0)回答 (1)
Q: What helix do I need for this engine? for plane
尋ねた bovemoisesgmailcom に 2019-03-01 12:13:12
msnowden Helix is not a term commonly used in RC planes. Electric engines are called motors to differentiate from the gassers. If you mean the backplate or mount on the firewall, it should be approximately 2mm to 3mm thick for this motor.
2020-01-13 03:41:34 役に立つ (0)回答 (1)
Q: how many poles are these motors? I just want to know what timing tor run them at. thanks
尋ねた seanzacharyuy に 2018-04-21 12:34:43
msnowden Recommend keeping the timing as it is. Experiment at 0° and increase 2° and measure for heat increases and efficiency.
2020-01-13 03:29:51 役に立つ (0)回答 (2)
Q: What is the shaft size(diameter) of the included prop adapter? Is it 6mm?
尋ねた Turbobeaver に 2020-01-11 09:40:04
msnowden The motor’s shaft is 3.17mm in diameter.
2020-01-13 03:23:34 役に立つ (0)回答 (1)
Q: Can you reverse shaft so motor can be mounted behind front bulk head?
尋ねた norkerr に 2020-01-03 11:35:22
msnowden Itis not advised.
2020-01-08 01:35:51 役に立つ (0)回答 (1)
Q: Can it back? Can it be used for RC Boat?
尋ねた shuchin に 2019-09-27 06:49:37
msnowden It does not back up or reverse. Probably not best for an RC boat.
2020-01-08 01:31:03 役に立つ (0)回答 (1)