招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: What are the Width, Height , and Depth, as well as thickness of the materials used.
尋ねた BG223118341 に 2021-10-08 07:04:00
回答 (1)
BG223118341
13/09/2021
BG223118341
31/08/2021
BG223118341
03/08/2021
尋ねた BG235224514 に 2021-07-04 09:51:58
BG223118341 4mm would be about right and you can but it at any hardware store. Tell them it is for a chainsaw.
2021-07-05 06:28:09 役に立つ (0)回答 (6)
BG223118341
18/06/2021
尋ねた penny に 2021-05-31 01:52:00
BG223118341 I do not believe that they sell new chains however, others do and they will fit.
2021-05-31 03:44:18 役に立つ (0)回答 (7)
BG223118341
03/05/2021
Q: This product exists in a larger size, a few kg load capacity?
尋ねた Chariot に 2021-04-04 06:47:18
BG223118341 Yes it does. On Eleksmaker,s site.
2021-04-04 06:56:35 役に立つ (0)回答 (1)
Q: Does anybody know how this works, can't see directions or instructions.
尋ねた BG361211134 に 2021-03-10 02:38:03
BG223118341 They have a video on how to use this product. I believe it is at the bottom of the page where the tools arew.
2021-03-10 06:57:59 役に立つ (1)回答 (11)
尋ねた Scott Bradley に 2021-02-24 01:19:44
BG223118341 You may get away with corner brackets or end plates.
2021-02-24 06:21:19 役に立つ (0)回答 (3)
尋ねた mvilmos に 2021-02-12 02:04:52
BG223118341 I can `t see why not, if your board can handle the amps and you watch orientation of the A+ A- B+ B- (red blue green black).
2021-02-12 03:17:42 役に立つ (0)回答 (1)
Q: Hello, do I have a question? Is it a compatible with Atomstack A5 - 20W? Thank you for answer.
尋ねた BG114252315 に 2021-02-04 09:11:43
BG223118341 I am not an expert on Atomstack A-5, however the #17 stepper motor uses 1.3 amp to operate. You may need a 4th axis to run the elecks rotate. If the steppers on the Atomstock are #17, I do not see a problem. If the Atomstack uses 2 steppers, then you will need a board that drives 3 steppers.
2021-02-04 09:32:13 役に立つ (0)回答 (2)
Q: will this rotary unit work with the neje master master 20w laser engraver?
尋ねた damnnoid に 2021-01-28 08:31:00
BG223118341 The rotation is done by the stepper motors, which get their signal from the stepper drivers. The laser is controlled on its own from the board. I hope this is of some help.
2021-01-28 09:28:20 役に立つ (0)回答 (1)
Q: Can this work with the atomstack lazer engraver??
尋ねた BG192254123 に 2020-12-18 08:02:24
BG223118341 I can not say for sure, however I believe if the laser is set properly I can,t see why not. (meaning the height, focal length.)
2020-12-18 09:24:45 役に立つ (0)回答 (1)
BG223118341
07/10/2020
BG223118341
07/10/2020
BG223118341
07/10/2020
尋ねた Anil に 2019-06-20 06:26:57
BG223118341 Iam disappointed as the rods are too short. It would be better if you cut the aluminum profiles to match the large diameter of the rods, so the small end could fit in the bearings as they should. It would make for a better product.
2020-09-19 10:02:32 役に立つ (0)回答 (1)
The seller Sliding table size：40*70mm
2021-10-08 08:33:06 役に立つ (0)