すべてのメッセージ

Nelly Using Steps: 1. Clean the table. 2. The vise is placed in table, firmly press the base of wrench and control the handle suck table. 3. The workpiece clamping on the forceps, then can be processed operation.

2020-08-06 01:35:42 役に立つ (0)
提出
回答 (1)

Q: does it contain 10ohm resistor???

尋ねた Kumar Pallav に 2018-04-07 11:43:22

DuaneMHunt1976 0ohm,2.2ohm, 4.7ohm, 5.6ohm, 7.5ohm, 8.2ohm, 10ohm, 15ohm, 22ohm, 27ohm, 33ohm, 39ohm, 47ohm, 56ohm, 68ohm, 75ohm, 82ohm, 100ohm, 120ohm, 150ohm, 180ohm, 220ohm, 270ohm, 330ohm, 390ohm, 470ohm, 510ohm, 680ohm, 820ohm, 1Kohm, 1.5Kohm, 2.2Kohm, 3.3Kohm, 3.9Kohm, 4.7Kohm, 5.6Kohm, 6.8Kohm, 7.5Kohm, 8.2Kohm, 10Kohm, 15Kohm, 22Kohm, 33Kohm, 39Kohm, 47Kohm, 56Kohm, 68Kohm, 75Kohm, 82Kohm, 100Kohm, 150Kohm, 180Kohm, 220Kohm, 330Kohm, 470Kohm, 560Kohm, 680Kohm, 1Mohm, 1.5Mohm, 2Mohm, 3.3Mohm, 4.7Mohm, 5.6Mohm, 10MohmN THE LIST IT SAYS 10 Ohms!!

2020-06-12 01:49:59 役に立つ (0)
提出
回答 (2)

DuaneMHunt1976 Inmy time of using SMD Cap or Res i have never seen a maker, it does the job and thats normally all one can ask from it

2020-06-12 01:48:16 役に立つ (0)
提出
回答 (2)

Q: Which values content? How many each?

尋ねた Juan Pablo Moriatis に 2019-09-11 07:32:44

DuaneMHunt1976 MaybeRead the ADVERT! it does say what values are in the PACK and how many of EACH! and on that NOTE, i wouldnt know in Person as It DID not Turn up! Guess too CHEAP to be TRUE

2020-05-11 03:15:50 役に立つ (1)
提出
回答 (2)

Q: Can I use this connector to power my TS100 soldering iron ?

尋ねた MarcAntoine に 2019-04-18 04:35:22

DuaneMHunt1976 wellthis is just the connector, so if you have a Transformer (RIGHT AMPS and VOLTS, and CABLE that can handle it) But if your asking if this is RIGHT for a SET Soldering Iron, im a bit scared that you may not know what you are doing.

2020-05-11 03:14:36 役に立つ (0)
提出
回答 (4)

Q: Contiene resistencias de 220 ohms y 560 ohms?

尋ねた vanyAranda に 2019-06-29 01:27:49

DuaneMHunt1976 No sabría, el artículo nunca apareció.

2020-05-11 03:11:33 役に立つ (0)
提出
回答 (2)