招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: The current is indicated correctly up to 0.001 A , compared to a good multi-meter ?
尋ねた MihaiP に 2019-09-05 01:05:12
回答 (2)
Q: i don't see any IR led on this, how is the nght vision? ;
尋ねた theGeezer に 2022-03-01 08:02:23
MihaiP Not visible on the image, but the IR works fine, as indicated in the documentation.
2022-03-01 08:37:12 役に立つ (0)回答 (2)
Q: What is the speed of the linear actuator?
尋ねた BG441812575 に 2021-11-27 04:41:03
MihaiP Depends on the stepper motor driver. Count on several seconds per 100 mm, as fastest move. The lowest is as slow as you want!
2021-11-27 05:48:38 役に立つ (0)回答 (1)
Q: Does the SD card on this module work on the Arduino Mega ?
尋ねた BG154735114 に 2021-10-22 11:45:17
MihaiP Surely ! You can watch pictures from SD on the display, with appropriate Arduino library.
2021-10-23 02:12:20 役に立つ (0)回答 (3)
尋ねた BG414851417 に 2021-09-08 04:49:45
MihaiP Look in grabcad.com library slide-axis-table-1#!
2021-09-09 12:49:24 役に立つ (0)回答 (1)
MihaiP
15/11/2018
尋ねた Moirianos に 2021-06-15 07:04:37
MihaiP Not recommended. Notebook manufacturers require to use only their adapters, since most of them are not just AC-DC converters.
2021-06-15 08:27:17 役に立つ (0)回答 (1)
Q: can this play files streaming on the internet with suitable connection to wifi with arduino?
尋ねた BG422441011 に 2021-05-06 06:32:10
MihaiP No, it reads the sound files from SD only. There are other boards for what you need.
2021-05-07 12:47:05 役に立つ (0)回答 (5)
MihaiP
08/10/2019
尋ねた lensman11 に 2021-04-18 12:50:44
MihaiP According to product information: "The backlight is always on, cannot control the backlight: backlight is connect to 3.3V"
2021-04-18 02:35:45 役に立つ (0)回答 (1)
尋ねた BG231039414 に 2021-02-01 02:48:01
MihaiP Zero volts is wrong! Possible causes: Power it at 3.3V only! Use analog read but in a 3.3V board! My readout: about 620 (2 V in air) and 310 (1V) in water. You must calibrate yours.
2021-02-02 07:50:44 役に立つ (0)回答 (4)
尋ねた BG491718209 に 2020-12-31 11:00:28
MihaiP Check the switches of the board. Set it to Mega and test it in Arduino. Works fine. Then try WiFi alone. All together is for advanced users.
2020-12-31 11:18:47 役に立つ (1)回答 (2)
Q: it says adjustable. how to adjust?
尋ねた BG101554944 に 2020-12-12 06:51:01
MihaiP You can adjust with the small trimmer: any output voltage between 0 and about 1.5 V below the input voltage.
2020-12-13 01:43:17 役に立つ (0)回答 (4)
Q: does it have accelerometer on board?
尋ねた katseros に 2020-12-02 04:37:23
MihaiP No
2020-12-02 01:18:42 役に立つ (0)回答 (1)
Q: There is no dimension for mounting surface to mounting surface. Can you provide?
尋ねた BG419535339 に 2020-09-23 11:29:33
MihaiP Platform 45x40mm. Distance between out-most channels: 30mm.
2020-09-29 01:06:40 役に立つ (0)回答 (1)
Q: Can a IC chip span the gap the same as the standard plastic breadboard?
尋ねた BG435423340 に 2020-08-03 12:22:30
MihaiP Yes, the spacing over the gap is perfect for IC chips.
2020-08-03 02:12:21 役に立つ (1)回答 (2)
尋ねた jhowarth に 2020-07-20 05:17:03
MihaiP The box must remain of reasonable size. It covers several lengths, enough in most cases.
2020-07-21 12:29:41 役に立つ (0)回答 (3)
MihaiP
11/06/2020
BENHAMMOU yes
2022-04-20 11:31:29 役に立つ (0)