招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Soultrap102
09/02/2022
Just fitted. Comes with everything you need and more. Z stays in sync without any help.
Ender 3 Ender 3 pro Ender 3 V2 3Dプリンター用のリードスクリューカップリングステッパーモーターを備えたCreativity®デュアルZ軸アップグレードキット
US$49.99
0
推奨事項
コメント (1)
Q: What should I buy besides this kit to install it on the ender3v2?
尋ねた BG101643191 に 2020-11-26 05:56:37
Soultrap102 Agree with answer from Halinalle
2022-02-27 02:42:38 役に立つ (0)回答 (2)
尋ねた jimfrag に 2021-09-18 05:02:07
Soultrap102 Hi, they don't come with sd cards. They re pre installed with the default firmware for ender 3.
2022-02-26 08:07:54 役に立つ (0)回答 (2)
Soultrap102
26/02/2022
尋ねた gpschmidt に 2019-12-06 10:37:31
Soultrap102 This will fit on a ender 3 pro
2022-02-26 08:07:03 役に立つ (0)回答 (6)
Soultrap102
26/02/2022
Soultrap102
26/02/2022
尋ねた sutees に 2020-08-29 09:55:22
Soultrap102 If the Biqu b1 supports BLtouch this will work. Just check if you need longer cables.
2022-02-19 03:17:58 役に立つ (0)回答 (3)
Q: questa scheda va bene per anet a8 plus ?
尋ねた AngeloDonofrio に 2021-06-07 04:47:49
Soultrap102 It was made as a drop in replacement for the ender 3. But many people have used them for custom printers.
2022-02-18 01:47:32 役に立つ (0)回答 (2)
Q: This will work for an Ender 3 V2?
尋ねた BG571855590 に 2020-12-16 03:34:01
Soultrap102 The ender v2 has a probe port. Just make sure you check what order you connect the pins.
2022-02-18 01:46:19 役に立つ (0)回答 (3)
Soultrap102
12/02/2022
Q: va bene su scheda madre skr 1.4 turbo?
尋ねた guido_1982 に 2020-01-12 02:58:39
Soultrap102 Not sure, but it works on my skr mini v2 for ender 3
2022-02-09 06:28:27 役に立つ (0)回答 (2)
Q: Will this work on an Anet A8?
尋ねた colly に 2018-11-27 12:09:37
Soultrap102 Based on size of bed. Ender is a little bigger than some 3d printers
2022-02-09 06:27:32 役に立つ (0)回答 (3)
Q: Is it possible to provide a 2-meter extension?
尋ねた BG231016434 に 2020-09-08 03:41:09
Soultrap102 I also found the extension a little short
2022-02-09 06:25:59 役に立つ (0)回答 (3)
Soultrap102
09/02/2022
Q: Does it work with Ender 3 ?
尋ねた panmourtas に 2020-04-15 01:00:58
Soultrap102 Yes worked for me. It takes over the Z stop. You may need to install custom firmware to add mesh bed leveling.
2022-01-18 05:27:39 役に立つ (0)回答 (3)
Soultrap102
17/01/2022
Soultrap102
17/01/2022