招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
danarrib
16/12/2020
Q: Does this props needs to be balanced?
尋ねた danarrib に 2019-10-23 10:04:19
antomolog у меня почти идеальные
2021-10-09 12:33:16 役に立つ (0)回答 (2)
Q: كم بطارية استطيع وضعها في كل خلية
尋ねた abuamroamaireh に 2021-02-05 05:52:03
danarrib You can wire in parallel as many as you want.
2021-08-04 12:44:34 役に立つ (2)回答 (3)
Q: I just wish that 7, 8 and 9 inch versions had 5mm or 6mm arm thickness instead of 4mm arms
尋ねた danarrib に 2021-04-15 08:51:02
CutieePie You can change the arm.
2021-05-07 03:34:17 役に立つ (0)回答 (1)
尋ねた danarrib に 2020-08-15 05:54:18
tedhancock68 When I started making packs I thought I didn’t need any balancing at all since I was using new, Japanese cells and slow charging. Now, $300 in lost batteries has convinced me to permanently install one of these on every pack. It adds 50 - 100% to the cost of a pack, but very much worth it!
2020-12-23 10:37:51 役に立つ (0)回答 (3)
尋ねた BG123242234 に 2021-03-14 09:37:24
danarrib This board doesn't work AT ALL.
2021-03-14 12:08:02 役に立つ (1)回答 (2)
Q: Does it work with iPhone 11 Pro Max?
尋ねた danarrib に 2021-01-06 07:52:41
Apogee mxkmxk1 Yes, it does.
2021-02-05 06:11:51 役に立つ (0)回答 (1)
Q: How can it be programmed? Where's the Instructions Manual?
尋ねた danarrib に 2020-01-24 12:29:22
BG561117159 where can I find programming instructions please?
2020-09-01 11:29:05 役に立つ (0)回答 (1)
Q: Can you please send a picture of the back side of this board?
尋ねた danarrib に 2020-11-10 07:02:28
tedhancock68 You mean is there any components, traces, or electrical conductivity on the back? If that is your question then...no. It is well insulated on the back side with some rubbery coating and conformal.
2020-12-25 03:36:17 役に立つ (2)回答 (2)
danarrib
25/11/2020
danarrib@DrDuckFPV No, for 7 inch props I'm using 4S or 3S. 6S is too much for 7 inch on this motors.
danarrib
29/11/2019
2
コメント (4)
danarrib
29/11/2019
尋ねた danarrib に 2020-03-09 01:06:20
Martin The XSR receiver inside could easily sent telemetry data to your transmitter. But I doubt most of the simulator softwares will transfer these data to the XSR.
2020-11-02 05:43:42 役に立つ (0)回答 (2)
Q: What's the differente between T7056C and T7056C PRO version?
尋ねた danarrib に 2019-11-26 02:23:58
BG114816400 The Pro version has more material on the connection point between hub and blade. The old ones were prone to explode when running 6S Low kv setups.
2020-10-29 01:48:47 役に立つ (0)回答 (2)
Q: When the 1550kv version will be available?
尋ねた danarrib に 2020-09-19 04:25:35
Hattiv Around Oct 26th
2020-10-09 06:03:22 役に立つ (1)回答 (1)
Q: If it has a Barometer and I2C pads, would be PERFECT.
尋ねた danarrib に 2020-08-08 11:28:40
BG454816422 According to the datasheet of STM32F722 LQFP64 and the HIFIONRC Betaflight unified target board definition, the MCU pins B10 and pin B11 (TX3,RX3 on solder pads) should be mappable to I2C device 2. No guarantees, but I'm going to attempt using that.Update: tried and it's working. I have a BMP280-3.3. VCC of baro is connected to the 3.3V PAD, SCL of baro is connected to TX3, SDA of baro is connected to RX3. Here are the betaflight configuration changes to make it work:resource SERIAL_TX 3 NONEresource SERIAL_RX 3 NONEresource I2C_SCL 2 B10resource I2C_SDA 2 B11set baro_bustype = I2Cset baro_i2c_device = 2set baro_i2c_address = 0set baro_hardware = AUTO
2020-10-06 05:30:11 役に立つ (2)回答 (2)
JohnHutch they do...search
2022-07-31 10:11:32 役に立つ (0)