招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: Does this item have a built in burden resistor?
尋ねた zamlaurie に 2021-12-28 10:26:32
thebreadboard Pretty sure it does not, the case specifies 50mA output for 100A input. If you need a voltage out then you can either order one specifically with voltage out or simply add a suitable burden resistor
2022-01-15 01:00:38 役に立つ (0)回答 (2)
Q: ele permite controlar a potência do laser? talvez por PWM?
尋ねた ginatto に 2018-03-30 06:45:38
thebreadboard Theremodules do have a PWM input so yes you could control the average power that way, remember though that when the LED is on it is emitting full power so it is still quite powerful even when using PWM and results will vary depending on many other control factors.
2021-04-19 11:36:15 役に立つ (0)回答 (1)
尋ねた Theknuttygarage に 2019-08-13 04:49:38
thebreadboard Theselow powered laser diodes are not the best for cutting anything beyond paper, thin foam etc, for penetration it would be difficult to say, again, depends on material and also PWM will always be full power when on. to answer your direct question, yes you could use PWM to control the average power used in engraving and or "cutting". what is it your going to be cutting 6hr per day ?, if you tell me then I could give a better answer
2021-04-19 11:33:51 役に立つ (0)回答 (1)
Q: hi, es compatible con ***** ? o necesito algo mas?
尋ねた BG822221340 に 2021-04-15 06:05:09
thebreadboard youwould need the one without the CCFL transformer board, this display seems to be LED backlight so its not needed. you may also need to re-program it as per instructions, all easy to do and the board does support the resolution
2021-04-19 11:00:17 役に立つ (0)回答 (1)
Q: Support this Model No : LP141WX3 TL B2 ?????
尋ねた BG143920131 に 2020-11-09 11:58:04
thebreadboard lookslike it should work, the cable is 2 channel vs the panel that is 1 channel but it will ignore the extra channel. you will need to program the board as I showed on my YouTube video , look for youtube channel thebreadboardca and you will find the related videos there.
2020-11-21 01:36:06 役に立つ (0)回答 (1)
Q: Is b156htn03.8 compatible with this?
尋ねた BG335124495 に 2020-11-14 07:58:10
thebreadboard That'san LVDS controller and you panel is eDP, also your panel uses LED back light, but product comes with an CCD driver.
2020-11-21 01:31:32 役に立つ (0)回答 (1)
Q: Hi, could you tell me if this laser is possible to make the recording in aluminum?
尋ねた Thiago Varasquim に 2018-09-17 01:36:38
thebreadboard Idoubt it on bare aluminum, but if it is painted first then it should be possible, I have not tried this though. google "laser etch aluminum 450nm" you should be able to find some videos on the topic
2020-11-21 01:27:56 役に立つ (0)回答 (1)
Q: How can I change the bits? it is with 8 bits and my screen is 6
尋ねた BG571154812 に 2020-11-08 12:54:32
thebreadboard asfar as I am aware, it is just a case of selecting the right cable, sometimes there is also a config in the controller, this depends on the controller of course
2020-11-11 04:56:13 役に立つ (0)回答 (1)
Q: Will this board work with LP156WHB TL A1 screen ? it's a LG panel , 15.6 inch 1366x768 resolution
尋ねた BG814131281 に 2020-10-24 06:48:09
thebreadboard I looked at the data from panellook.com and it all matches so based on that it should work
2020-10-24 10:49:23 役に立つ (0)回答 (1)
Q: Will this 8 mm one fit the CR-10S Pro V2?
尋ねた iPavan に 2020-09-28 11:34:35
thebreadboard Almost every 3D printer in this class or price range uses the 8mm lead screw in one way or another, more expensive models' may move to ball screws but there way more expensive typically
2020-09-28 05:57:50 役に立つ (0)回答 (2)
尋ねた dsanchez に 2018-12-07 02:15:53
thebreadboard GND.VCC and SBUS - IBUS depending on how you config BetaFlight. PWM is mostly used as a legacy connect direct to servos etc.
2020-09-28 05:56:10 役に立つ (0)回答 (1)
Q: I don't see any hall wires coming out of the motor?
尋ねた Bremmola に 2020-06-08 12:20:25
thebreadboard Thereare none, the motor controller assumes the motor is able to keep up , some controllers can actually measure the back EMF to determine the state of the motor, detect stalls etc, most controllers also measure the current draw to determine the load and detect a stall.
2020-09-28 05:52:22 役に立つ (0)回答 (1)
Q: Is it able to use with RUSH TANK 5.8G 48CHjQuery111305965158743168963_1592192796652
尋ねた BG131349364 に 2020-06-14 10:46:39
thebreadboard The band frequencies are the same for most all of the VTX transmitters and Receivers, this one looks to be the standard as well so I think it will work very well with this receiver.
2020-06-14 11:16:02 役に立つ (0)回答 (1)
Q: Hello, do you make invoices when I buying the product?
尋ねた MiwelitoHernand に 2018-05-23 09:34:47
thebreadboard goto the details page of the order and you will see a button near the bottom of the page that will "Print Invoice"
2020-06-10 11:57:56 役に立つ (0)回答 (1)
thebreadboard Looks like a simple linear antena, so it will depend on orientation of mounting. Straight up and down would be verticle, parallel to the ground, horizontal
2022-06-21 06:46:25 役に立つ (0)