すべてのメッセージ

TAC@TonyCL Hi Tony. I ran a number 10 x 3 wire cable to my bathroom from the main electrical panel. And added a 2 x 40 amp circuit breaker switch to the panel. Works fine. See my newest review I posted today.

TAC 18/11/2020
Received this water heater (Product ID 1721621 SKUF56991) yesterday and today installed it. It works, but just barely. Here is what I found. 1. The heater is rated at 3500 watts and I measured 3565 watts when it was running. The power cord gets very warm because the wire size is too small. 2. The English language instruction manual is useless, because the translation from Chinese to English is terrible. 3. The LED temperature display on the water heater does not display input or output water temperature. I have no idea what the numbers relate to. 4. With input water temperature of 11C, the output water temperature is 31C. That is just barely warm enough water for use in a shower. The LED temperature displayed about 50C which is meaningless. 5. This water heater works by heating water flowing past a heating element. The slower the water flow, the higher the output water temperature. To get 31C water for showing, the water flow rate was reduced to just above the minimum flow rate needed to turn on the water heater. Less than that flow rate, the heater shuts off. 6. So, I was able to shower, but with water that was lukewarm, not hot. Any lower temperature and I could not use it. 7. And, at that barely adequate lukewarm temperature, the water flow was very low. I tried 4 shower heads and only 1 worked, and that was not the included shower head. 8. It seems 3500 watts is not enough power to heat water for showering purposes. And, the input water temperature will only go lower here as winter has not yet arrived. 9. The only positive trait I found was that the water temperature was very stable. For that I rate it 5 stars!
0
コメント (3)
TAC 18/11/2020
Received this water heater (Product ID 1721621 SKUF56991) yesterday and today installed it. It works, but just barely. Here is what I found. 1. The heater is rated at 3500 watts and I measured 3565 watts when it was running. The power cord gets very warm because the wire size is too small. 2. The English language instruction manual is useless, because the translation from Chinese to English is terrible. 3. The LED temperature display on the water heater does not display input or output water temperature. I have no idea what the numbers relate to. 4. With input water temperature of 11C, the output water temperature is 31C. That is just barely warm enough water for use in a shower. The LED temperature displayed about 50C which is meaningless. 5. This water heater works by heating water flowing past a heating element. The slower the water flow, the higher the output water temperature. To get 31C water for showing, the water flow rate was reduced to just above the minimum flow rate needed to turn on the water heater. Less than that flow rate, the heater shuts off. 6. So, I was able to shower, but with water that was lukewarm, not hot. Any lower temperature and I could not use it. 7. And, at that barely adequate lukewarm temperature, the water flow was very low. I tried 4 shower heads and only 1 worked, and that was not the included shower head. 8. It seems 3500 watts is not enough power to heat water for showering purposes. And, the input water temperature will only go lower here as winter has not yet arrived. 9. The only positive trait I found was that the water temperature was very stable. For that I rate it 5 stars!
0
推奨事項
コメント (3)

TAC It would be unsafe to use the shower without the earth wire connected. If I had your GFI (GFCI) tripping problem, I would not use the GFI and instead would connect the shower directly to 240 volt power with a fuse or circuit breaker of appropriate size.

2021-02-20 03:04:55 役に立つ (1)
提出
回答 (3)

BG221411469 Hello, there is a temperature control switch to adjust the temperature

2020-10-14 09:27:16 役に立つ (0)
提出
回答 (1)