招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: should i use battery when i upload the code from arduino ?
尋ねた BG208434018 に 2021-03-25 02:58:15
回答 (1)
Q: Is this working with ender 5 motherboard 1.1.5?
尋ねた miodragp7 に 2021-03-17 02:54:13
Leon I'musing it with the Creality 1.1.5 board in an Ender 3 Pro. I don't now if the differences between Ender 3
2021-03-17 04:23:14 役に立つ (1)回答 (1)
Q: Can you also flash the bootloader with this kit?
尋ねた andr00ahayes1967 に 2021-02-08 06:24:45
Leon I was unable to get he included USB adapter to work with my Windows 10 laptop. Instead of pursuing it deeply, I upgraded to the 1.1.5 mainboard. This came with a bootloader and silent stepper drivers.
2021-02-08 11:33:21 役に立つ (1)回答 (2)
Leon
29/05/2018
Leon
20/02/2020
尋ねた fke に 2021-01-07 09:48:15
Leon I used the tft-espi library. There are many tutorials online to help.
2021-01-07 09:54:30 役に立つ (2)回答 (2)
Q: Is there schematic diagram in PDF? Any sample programs in Arduino or MicroPython?
尋ねた Maja に 2020-08-23 10:53:33
Leon I found a great deal of useful info here -- ucexperiment.wordpress.com Look for the post from December, 2016
2020-08-23 11:23:04 役に立つ (0)回答 (1)
Q: Where can I get the schematic diagram?
尋ねた Leon に 2020-07-25 12:55:28
Badboy google search 1+Channel+5V+Relay+Module+30A+diagram
2020-07-25 03:47:30 役に立つ (0)回答 (1)
Q: What is the pin # of the onboad LED? I've tried 2 and 5 without success.
尋ねた Leon に 2018-12-20 11:33:01
realblades gpio.mode(2,gpio.OUTPUT); gpio.write(2, 1); gpio.write(2, 0); Worked for me with the stock LuaNode fw that it came with. You don't say what you tried exactly. Maybe you haven't changed the pin mode?
2020-05-10 04:29:48 役に立つ (0)回答 (4)
Q: Will this work with 3.3v logic? I understand it needs 5v Vcc. I want to use it with an ESP32.
尋ねた Leon に 2020-04-20 10:22:42
Bungeyner247 not work
2020-04-29 03:40:25 役に立つ (0)回答 (1)
Q: What is the pin number for the builtin LED?
尋ねた Leon に 2020-02-03 10:49:59
Encephaloid D2, D4?
2020-02-17 03:51:28 役に立つ (0)回答 (1)
Q: Does anyone have a link to install the drivers. I'm not sure what to search online. Thanks
尋ねた awaiskhawaja2003 に 2020-02-05 04:48:45
Leon The UART chip is the CP2102 from Silicon Labs. A search for that will get you to the download page.
2020-02-05 10:12:14 役に立つ (2)回答 (5)
Q: How duo you connect to the esp8266 to program it?
尋ねた David_J_Bryant に 2019-12-11 04:52:08
Leon Use P6 right next to the power terminals. The pins are labeled TX. RX. & GND. This is a serial port to upload the software. P5 right next to it is the Boot terminal. If these pins are connected together when the board is powered up,it goes into boot mode, ready to receive a software load. I use the Arduino IDE. I had to update to version 2.6.3 of the ESP8266 package to get reliable programming.
2020-02-04 03:23:53 役に立つ (3)回答 (2)
尋ねた Leon に 2020-01-25 09:24:16
Gossamer No power led. How do you use it?
2020-02-02 12:34:57 役に立つ (0)回答 (1)
Leon
10/01/2020
Q: What is the spacing for the board mounting holes?
尋ねた Leon に 2020-01-06 11:24:46
bwmitchem If you look at the picture with rulers you can tell
2020-01-08 08:22:41 役に立つ (0)回答 (1)
Q: What is the spacing for the mounting holes in the board?
尋ねた Leon に 2020-01-06 06:27:12
wujiahui about 60mm
2020-01-06 08:39:23 役に立つ (0)回答 (1)
Q: Whatis the pin number for the onboard LED? Pin 5
尋ねた Leon に 2019-05-14 12:26:53
Randon8 check the pinout
2019-05-24 01:40:20 役に立つ (0)回答 (1)
Leon If you are using the USB jack to upload, the host computer will power the board. You won't need the battery, but you don't need to remove it either.
2021-03-25 02:42:32 役に立つ (1)