招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
kelkie
04/08/2023
done the job unluck some i have had.
TWO TREES® タッチオートレベリングセンサーオートベッドレベリングセンサーBLTouch 3Dプリンター用
US$19.99
US$28.99
0
推奨事項
コメント (0)
Q: is this suitable for 18650 battery's
尋ねた kelkie に 2022-05-22 05:25:24
BG544584744 No
2023-01-04 09:25:55 役に立つ (0)回答 (2)
kelkie whattemp would you suggest as far as im concerned its crap but reading this im questioning my opinion on this stuff. thanks for review
Bill Tooth
16/10/2015
7
コメント (1)
kelkie
01/03/2022
Q: Is this lighter than average pla?
尋ねた kelkie に 2020-12-23 07:22:58
ImagineWorks Weightnetto 750grams. This was my first PLA and works great with the stock PLA setting of my printer of 210°C ~ 195°C, print speed 40 ~90 mm.p.s. They claim < ± 0.05 ~0.02mm accuracy. I measure between 1.75 - 1.74mm and use white - grey - black filament of this brand. Made fine prints with this.
2020-12-26 05:02:42 役に立つ (1)回答 (2)
尋ねた rcartier に 2021-07-07 03:54:04
kelkie 14.4 is 4s dude. please use calculator 11.1 is 3s 2s 7.4. what 7.4 x2 =
2021-07-20 05:09:45 役に立つ (0)回答 (2)
Q: which one do we believe????? Battery: 2-4 Li-po or Voltage: 7.4 -11.1 V
尋ねた kelkie に 2020-06-12 02:57:54
JLT_GTI the motor can take 2 to 4S .. but you will need to use a propeller so it wont go over the max Watts (270 acording to description) you would need a watt meter to test it or use an online power calculator considering its a 1000kv motor .. For example if you get 270W on 3S with a propeller you cant use the same propeller with 4S but could use a bigger one in 2S the key is not over-loading the motor
2020-06-22 10:44:44 役に立つ (4)回答 (5)
尋ねた masaki に 2021-05-10 01:30:52
kelkie you must also buy a transmitter. i suggest the tx16s iit is a great all transmitter that will grow with you and your hobby. hope this helps. also load of batteries and a pair of goggles
2021-05-11 04:27:15 役に立つ (1)回答 (4)
Q: Is it possible to control more then 1 set of these separately?
尋ねた kelkie に 2020-12-27 04:37:31
Yuki Not sure, I only bougth one set
2021-01-05 03:51:58 役に立つ (0)回答 (1)
Q: could you please tell me what the app is that it uses? so i can check it out while on the way to me
尋ねた kelkie に 2020-12-27 04:47:23
The seller LEDLAMP，scanning the QR code on the controller
2021-01-04 06:19:19 役に立つ (0)回答 (1)
Q: Is it possible to cut the LED stripes and use connectors? thanks
尋ねた matreco に 2020-12-08 06:27:22
kelkie yes it is possible. if you look at the strip there is solder or connector points x4. it is also possible to get joint and angle parts to attach.hope this helps.
2020-12-27 04:29:39 役に立つ (1)回答 (1)
Q: What's the 4 wire configuration on the plug? RSSI for the 4 the wire?
尋ねた Joe Cord に 2020-11-23 06:04:45
kelkie 5v, ground, ppm, and sbus are the 4 pins on the plug. look at last pic on the item page.
2020-11-24 04:17:52 役に立つ (1)回答 (2)
kelkie
08/11/2020
Q: hello, Can I connect a GPS module on this product?
尋ねた asuka15 に 2019-06-18 07:12:10
kelkie yes u can use a gps o this and also a compass. use uart2 and scl sda for compass. hope this help please like
2020-11-08 08:09:17 役に立つ (7)回答 (25)
kelkie same here it is a fault tell bg team they will sort u out
2020-10-10 05:51:02 役に立つ (1)回答 (14)
Q: Will these motors (https ://banggood.app.link/urkmiKvRpab) work and won't destroy ESC board?
尋ねた BG534610352 に 2020-10-08 07:27:48
kelkie please give a proper link i cant access it. or tell me what motors you are looking at
2020-10-10 05:47:46 役に立つ (0)回答 (2)
Q: Where can i find a controler software for this, help without it its useless?
尋ねた Tiago Carvalho に 2018-10-11 02:15:29
kelkie rx-pitch and rx-roll are pwm inputs
2020-09-10 06:45:42 役に立つ (0)回答 (2)
kelkie
28/08/2020
kelkie
28/08/2020