woodwaker
私のコンテンツ
すべてのメッセージ
レビュー
コメント
回答
質問

すべてのメッセージ

woodwaker 06/01/2018
I used this when mounting a LED COB. It worked the way it should moved the heat from the LED to the heatsink. was easy to use and very fairly priced
30g ヒートシンク熱伝導グリースコンパウンドペーストシリンジチューブ
3,72€ 13,05€
1
推奨事項
コメント (0)
woodwaker 01/02/2018
I had two problems with the assembly of the tester. I swapped the 3.3 K (3K3) and 33K resistor and had a solder bridge on one of the transistors. Be very careful with the resistors, as they are very hard to read and there are similar values used. It would be best to measure all then mark. Once I got it working then I tried to assemble the case. This is a puzzle as there are no instructions at all for the case.Do not use any of the parts that remain from the tester, use the bag of hardware that came with the case. I started with the bottom, use the shorter standoffs then put the tester board on these, thread the longer standoffs into these. The sides are fairly easy to figure out, as the openings only fit one way. I used masking tape to hold the sides together while I put the top and screws in. Take your time and it is a great kit.
DIY Mega328トランジスタテスターキット静電容量インダクタンスESRメーターダイオード三極管ケース付き
23,14€ 27,77€
5
推奨事項
コメント (0)
EleksMaker®EleksLaser- A3 Pro 2500mWレーザー彫刻機CNCレーザープリンター
309,37€ 371,80€

Q: hi there I just want to ask Is it possible to increase the frame size

尋ねた NABEEL に 2018-06-27 02:57:03

woodwaker I just finished upgrading mine to 1 meter side to side. You need 3 pieces the front and back and the laser head piece. You will also need a new belt for the laser motor. I made new cables for the two side motor. You can use one of the side motor cable for the laser motor, but will need a new laser cable. One i got all of the parts put together and cables working it was great..

2018-11-14 02:45:08 役に立つ (5)
提出
回答 (3)

woodwaker I think I have figured out the resistors - R9,R10 and R15 are 3.3K R11,R12 R13 and R14 are 50 Ohm. I'm not sure about R15, but it seems to work. I have no idea what the switches do (S1 to S3) the display changes when they are pushed, but not sure what they do. The instructions seem to be lacking on these points.

woodwaker 06/10/2018
I ordered this set of three car kits. I received two, and a third of the simple light tracking kit. The two correct kits look OK, but have no instructions at all, and there is no link on the product page. The schematic shown on the product page is NOT for this kit, but is the schematic for the simple light tracking car kit. I have no idea what the buttons do with out some kind of instructions or correct schematic
3PCS D2-4インテリジェントレンジングカーDIYキット超音波レンジモジュール10.8cm * 7cmボードサイズ
24,04€
1
コメント (1)
D2-4インテリジェントレンジングスマートロボットカーDIYキット 超音波測距モジュール 10.8cm*7cm板サイズ
12,10€ 14,90€

Q: Could you tell me the values for R9 to R15? they are not labelled on the board

尋ねた woodwaker に 2018-10-17 06:20:10

HOMIEEE R9(Color ring resistance)=10

2018-10-30 04:05:15 役に立つ (0)
提出
回答 (1)
D2-4インテリジェントレンジングスマートロボットカーDIYキット 超音波測距モジュール 10.8cm*7cm板サイズ
12,10€ 14,90€

Q: Quais são os valores das resistências R9, R10, R11, R12, R13, R14 e R15. O Kit vem acompanhado do esquema do circuito?

尋ねた Andrade に 2018-10-07 03:09:14

woodwaker I have the same question Could you tell me the values for R9 to R15? they are not labelled on the board

2018-10-17 06:18:54 役に立つ (2)
提出
回答 (1)
woodwaker 06/10/2018
I ordered this set of three car kits. I received two, and a third of the simple light tracking kit. The two correct kits look OK, but have no instructions at all, and there is no link on the product page. The schematic shown on the product page is NOT for this kit, but is the schematic for the simple light tracking car kit. I have no idea what the buttons do with out some kind of instructions or correct schematic
3PCS D2-4インテリジェントレンジングカーDIYキット超音波レンジモジュール10.8cm * 7cmボードサイズ
24,04€
1
推奨事項
コメント (1)

woodwaker Thanks, I was going to order this for my Eleksamker engraver

moderntools 12/04/2018
Product quality is very good, but not suitable to expand an Eleksmaker machine. When ordered, I assumed that the Eleksmaker's wheels would fit, but the profile is different in detail. I would be grateful if someone can advise where to buy Eleksmaker compatible profiles – many thanks in advance!
Machifit1000mm長さ2040TスロットアルミニウムプロファイルCNC用押し出しフレーム
25,15€ 30,74€
4
コメント (1)
woodwaker 20/02/2018
I have built 4 of these now. LOTS of fun. The first one had one bad digit, but still fun to build. A little tricky to set them with just one switch
3個のDIY 6デジタルLED電子時計キット9V - 12V AT89C2051
8,96€ 10,74€
0
推奨事項
コメント (0)
woodwaker 19/02/2018
I purchased these for my Elekslaser . Wanted to have some extras for visitors. These work well and are much cheaper than loosing your vision.
360nm-1064nmレーザー保護ゴーグルメガネIPL-2OD+ 4D for Laser
15,83€ 19,56€
0
推奨事項
コメント (0)
woodwaker 19/02/2018
a little tricky to get out, but works well, It would be nice if a plunger was included
DANIU 10cc 修復ツール はんだ PCB SMD はんだペースト フラックス グリース
8,15€ 14,90€
0
推奨事項
コメント (0)
woodwaker 19/02/2018
I purchased this to experiment with, for the price you can't goo wrong.
ESP32 開発ボード WiFi+bluetooth 超低消費電力 デュアルコア ESP-32 ESP-32S ボード Geekcreit for Arduino - 公式Arduinoボードとの互換性がある製品
9,31€ 19,56€
0
推奨事項
コメント (0)
woodwaker 19/02/2018
these are nice little kits to build. I have learned that on this inexpensive kits to buy at east two, so if you make a mistake you can learn from it and have one that works. The chip on a stick is a little tricky on how to install and solder.
3Pcs 16オルゴール16サウンドボックスキット電子DIYスイート
10,24€ 13,04€
0
推奨事項
コメント (0)
woodwaker 19/02/2018
I received it about 10 days ago, and took my time researching how to assemble. I got the newer version that does not have the corner metal pieces, so be careful to matcht information for the kit you received. You tube is the best way to get assembly directions. After experimenting and watching many you tube videos, I came across T2 Laser software. This is well worth the investment, you can try it for free and if happy purchase it . Overall I'm very impressed with this kit
EleksMaker®EleksLaser- A3 Pro 2500mWレーザー彫刻機CNCレーザープリンター
309,37€ 371,80€
0
推奨事項
コメント (0)
woodwaker 16/02/2018
I needed one of these for a project. 5 for the price was a great deal and I'm sure The rest will come in handy for something
5個5V電気磁気Activeブザー連続ビープ音連続
7,45€ 9,31€
0
推奨事項
コメント (0)
woodwaker 16/02/2018
I purchased 5 of these to hold small parts, The dividers can be removed to create different configurations
5個のGeekcreit® 15価値のある電子部品収納アソートボックス
12,10€ 14,90€
0
推奨事項
コメント (0)
woodwaker 16/02/2018
I have not tested yet, but knew that I would need an extra pair for my laser engraver. I am in the process of assembling the engraver and wanted to have a pair for anyone that looks at it.
EleksMaker®青紫色レーザーゴーグル安全メガネレーザー保護眼鏡
7,45€ 9,31€
0
推奨事項
コメント (0)
woodwaker 16/02/2018
I have done lots of soldering over the last 50 years, but never SMD's before. I built 15 of the smaller three color Christmas trees and they worked fine. Thought I would try this one with the MP3 player. The SMDs in the kit are much more difficult to solder, and this is not the best kit to learn how to do it. It is a good kit, but i really made a mess of it, learned a lot and got better as I went. I had solder bridges on the larger IC that I could not get clear, so took it off and the tree now works, but no MP3. Another suggestion, I learned from the smaller trees, built each tree part then test it with a battery pack or 5 volt supply before soldering everything together. I had a bad LED and put one in upside down, easy to fix when it is not soldered to the base. The kit included extra parts which is great, but caused me some concern until I figured out that there were extra parts. You will also need a good magnifying glass to read the SMD part numbers.
MP3機能付きクリスマスツリーColorful透明カバー付きRGB DIY LEDフラッシュキット
20,39€ 21,98€
0
推奨事項
コメント (0)
woodwaker 01/02/2018
Just as described. It is heavier than I thought which is good, doesn't move around. The parts cutouts are nice - pretty deep - parts don't jump out
DANIU 45x30cm マグネット熱絶縁シリコンパッドデスクマットメンテナンスプラットフォーム、磁気セクション付き
27,01€ 32,61€
0
推奨事項
コメント (0)

あなたは専門家です、あなたは助けることができますか？

招待メールを購読することを心から歓迎します！

購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。

他の人を助け、幸せになりましょう！

  • 申し込む

バッジについて

バッジはコミュニティに関連しており、ユーザーは質の高いコンテンツを作成したり、ミッションを完了したり、特別なアクティビティに参加したりすることでバッジを獲得します。特定の人には独自の専用バッジもあります。
CEOバッジ

CEOバッジの所有者はバングッドのボス。

獲得できるバッジはまもなく提供されます
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe