招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
BG203725422
07/12/2023
as described, very happy
Webasto Eberspacherヒーター用の燃料タンクセンダースタンドパイプピックアップクリップ1322632A
US$10.99
US$15.99
0
推奨事項
コメント (0)
Q: will this heater work with an afterburner controller
尋ねた BG501141750 に 2023-11-28 09:15:56
BG203725422 I believe that the Bluetooth controller and its mainboard are shown as not compatible with the afterburner controller. If you refer to the afterburner website they list which controllers are compatible and which are not compatible
2023-12-04 02:20:01 役に立つ (0)回答 (1)
Q: compatible pour alfawise i30 pro? et droite ou gauche ? Merci
尋ねた noto 60 に 2020-11-14 07:25:25
BG203725422 I do not know
2023-11-26 04:19:32 役に立つ (0)回答 (2)
尋ねた BG354518328 に 2020-09-14 02:12:25
BG203725422 I use file clips
2023-11-26 04:19:15 役に立つ (0)回答 (4)
BG203725422 No
2023-11-26 04:18:52 役に立つ (0)回答 (4)
BG203725422
18/04/2023
BG203725422
20/03/2023
BG203725422
17/03/2023
BG203725422
14/03/2023
BG203725422
20/02/2023
Q: Is this "Carborundum" coated glass?
尋ねた RENOxDECEPTION に 2021-04-26 05:29:34
BG203725422 Not sure about the carborundum glass, but I have 4 of these glass beds and use the un-coated side with a bed adhesive, gives very nice smooth finish to the parts. Let the glass bed fully cool down or I even put it my freezer before removing the prints, mostly they just pop off and because the glass provides a tough surface you don’t get damage if z-height offset is a little off.
2022-06-14 01:25:16 役に立つ (0)回答 (2)
尋ねた BG121738343 に 2021-02-01 09:55:57
BG203725422 Newer Creality printers come with press fit gears on the extruder stepper motors and are a pain to remove, but you can achieve this and the original motor will work fine. If you want a direct drive unit this should work but mounts will need to be purchased or printed to convert.
2022-06-14 01:21:14 役に立つ (0)回答 (3)
Q: Will this allow for printing with flexible filament?
尋ねた bmack に 2020-09-30 10:58:14
BG203725422 You can print tpu easier with dual gear extruder, but you must adjust z-height adjustment and slow print speed to get any success, don’t go too soft as jams and retraction become serious issues
2022-06-14 01:17:08 役に立つ (0)回答 (5)
BG203725422
12/06/2022
BG203725422
12/06/2022
尋ねた simon に 2021-01-16 03:45:22
BG203725422 Yes, you may need new stepper motor as Creality push fit extruder gears and you also need to adjust e-step values
2022-05-30 11:58:44 役に立つ (0)回答 (2)
Q: Does it fit Ender-3 V2? Thanks
尋ねた BG651411359 に 2020-12-26 02:39:57
BG203725422 Yes, but remember you may need a new stepper motor as Creality use push fit gears and adjust your e-step values
2022-05-30 11:57:46 役に立つ (0)回答 (3)
尋ねた liebendan に 2021-08-29 01:02:56
BG203725422 I don’t know sorry
2022-05-30 11:56:53 役に立つ (0)回答 (3)