招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: Why on one side does it say 45c and on the other side it say 100c? is this 45c or 100c?
尋ねた milkydeathgrind に 2021-08-12 12:33:31
回答 (1)
尋ねた BG112325140 に 2022-03-03 02:33:39
milkydeathgrind you format the SD card as FAT32 default cluster size.
2022-03-03 09:45:19 役に立つ (0)回答 (1)
Q: What is the bullet connecter size?
尋ねた BG179495414 に 2022-02-25 03:19:40
milkydeathgrind these do not come with bullet connectors because it is just dead weight for a quick connector you do not need.
2022-03-03 09:42:17 役に立つ (0)回答 (1)
尋ねた Joe Foster に 2021-07-29 12:55:21
milkydeathgrind Youare able to select the 1 piece version or the 2 piece version though so what you stated isn't entirely true.
2022-01-03 03:53:50 役に立つ (0)回答 (1)
Q: which revision has the board?
尋ねた BG141914217 に 2021-01-18 06:29:02
milkydeathgrind Ifyou mean which version of the circuit board this has then it is the 2020.03.13 B6-80W V:3
2021-07-03 11:08:37 役に立つ (2)回答 (2)
尋ねた Shoshone Edwards に 2021-05-12 09:53:31
milkydeathgrind Youcan use any receiver you like with this. You can also use any other electronics that you want in this because it DOES NOT COME WITH ELECTRONIC PARTS.
2021-07-03 10:56:47 役に立つ (1)回答 (2)
Q: Will this fit the FrSky XJT module?
尋ねた Steve_Goral に 2021-03-20 07:53:18
milkydeathgrind Yesit will. It can fit any type of module that will fit into the external bay (same size\pins as frsky X9D\X9D ) OR even additional options via the two additional UARTs that are on the bottom of this radio.
2021-03-20 06:04:44 役に立つ (0)回答 (2)
尋ねた milbroman に 2021-02-05 09:25:28
milkydeathgrind I'mnot sure what you are asking exactly. If you are trying to ask if you can use a receiver that does not need to use the BEC from the esc then the answer is yes. This is simple enough to not need a video. If you don't want to use the ESC's BEC then just remove the 5v and ground wires (red and black) from the 3 pin connector coming from the ESC and only use the white SIGNAL wire and you essentially have stopped the BEC from being used.
2021-02-20 07:52:42 役に立つ (0)回答 (1)
Q: Can the color change dynamically being controlled by LUA scripting ?
尋ねた BG411222222 に 2021-02-08 08:02:52
milkydeathgrind No because this is only directly connected to a 5v power output and a ground source. Essentially it does not matter where that power is coming from but there is no data link in this connection set up.
2021-02-10 01:13:59 役に立つ (0)回答 (1)
尋ねた Hattrick に 2020-06-01 10:22:46
milkydeathgrind You can not put a receiver on uart 1. uart 1 is used for MSP while plugged in for the usb port. your micro usb uses uart 1 to connect to the computer. You could technically use uart 1 for receiver when it is not connected to the computer but then obviously you would have no way to set up your radio. Use UART 2 for sbus and if you are going to use smartaudio or tramp I recommend using uart 6 (which is a softserial port by the way).
2020-12-04 03:48:57 役に立つ (0)回答 (3)
尋ねた 2p7wppl に 2019-01-05 05:36:46
milkydeathgrind You need to buy a Frsky transmitter that uses the D8 or D16 protocol which is basically any radio that Frsky makes. I recommend the X9D plus if you aren't on a budget because you will never need to upgrade or have any other radio for other models.
2020-06-08 08:46:39 役に立つ (1)回答 (1)
milkydeathgrind
21/04/2020
Q: Is this receiver compatible with Taranis X-Lite?
尋ねた Spaniard76 に 2019-05-22 07:10:09
milkydeathgrind As of right now the ACCESS protocol which the X-lite uses can only be flashed on to MOST* D16 receivers and the D4R is a D8 protocol receiver. Short answer, no, you can not as of right now flash the ACCESS protocol on to this receiver, although this may change in the future. Your best bet would be to get a D16 receiver BUT you will still need to flash the ACCESS protocol on to these receivers (which is not difficult at all).
2019-11-04 06:03:38 役に立つ (1)回答 (1)
BG401349232 Its a 45c battery
2021-11-04 12:04:56 役に立つ (0)