招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Samppa78
16/05/2023
Not a precision square,mating surfaces are not flat, the part where bottom contact upper part is not in the same line. So this needs to be flat but its not. Bottom part is only screwed with 2 bolts that had stripped threads and bottom part holes doesn't align with upper part correctly. So poor quality and failed quality control. Will not purchase again,as advertised item us not what you actually get.
Drillpro マシニストスクエア 90º 直角 エンジニア キャンパー スクエア シート プレシジョン グラウンド スチール 硬化角定規
US$9.49
US$19.99
1
推奨事項
コメント (0)
尋ねた Samppa78 に 2021-01-10 09:41:29
brocak Not for such load, maybe 0.5 amps low power
2021-01-10 11:57:52 役に立つ (1)回答 (3)
Q: Will this antenna fit and work with jianpai 8800 pro?
尋ねた Samppa78 に 2022-04-24 12:32:33
viliambang The diameter of the ring is larger by approx. 0.5 mm, it needs to be ground
2023-07-02 05:46:51 役に立つ (1)回答 (3)
Samppa78
05/10/2023
尋ねた Samppa78 に 2023-04-08 03:43:38
回答 (0)
Q: Hi.What is the maximum flow rate for this hotend?
尋ねた Samppa78 に 2023-04-07 07:23:42回答 (0)
Samppa78
16/01/2023
尋ねた gpschmidt に 2019-12-06 10:37:31
Samppa78 This product fits ender 3 pro with surface size 235x235.
2022-11-28 10:44:45 役に立つ (0)回答 (6)
尋ねた ph001 に 2020-06-19 11:16:55
Samppa78 I haven't tested phone app.
2022-11-28 10:44:08 役に立つ (0)回答 (2)
Q: is it suitable for raspberry pi 2
尋ねた mbnngp に 2019-09-12 01:56:36
Samppa78 No.
2022-11-28 10:43:01 役に立つ (0)回答 (4)
Q: what is the maximum ampere hour of this BMS
尋ねた BG453216433 に 2020-11-19 11:23:50
Samppa78 Contact customer support for more info
2022-11-21 01:05:50 役に立つ (0)回答 (2)
Q: Is this compatible with the Ender 3 Max?
尋ねた BG535361435 に 2022-01-29 11:35:57
Samppa78 Yes.
2022-11-21 01:05:18 役に立つ (0)回答 (2)
Q: is possible cut the profiles regarding to my size needs?
尋ねた Eddie Piazza に 2020-09-18 06:47:53
Samppa78 Contact customer support
2022-11-21 01:05:16 役に立つ (0)回答 (2)
Samppa78
14/11/2022
尋ねた BG438161891 に 2022-07-21 07:45:42
Samppa78 As long as the battery pack doesn't exceed tester maximum voltage then its okei. However it will take many hours to test a big battery pack. Notice ohm law when you test battery's, depending on the set voltage you will be able or not to pull 180W. This is a maximum for this tester and you can burn mosfet. Run this device at max 150W and before use remove cooler and make sure that thermal compound is present.Just to be safe replace for better quality thermal paste.
2022-11-13 06:36:34 役に立つ (0)回答 (1)
Q: Can I use this for my mini 7 egg incubator?
尋ねた BG541355221 に 2022-09-06 05:13:37
Samppa78 If the fan specs are the same and fan model then why not?
2022-11-13 06:30:08 役に立つ (0)回答 (1)
尋ねた Fred に 2022-11-13 06:15:17
Samppa78 This is a part cooling fan.The same that you will find on any Ender series 3d.Intended to cool printed parts during printing process. Its a blower fan.
2022-11-13 06:27:49 役に立つ (0)回答 (3)