招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
尋ねた BG913244111 に 2023-05-06 01:56:49
回答 (1)
Q: does it come with a soldering wire?
尋ねた BG118474114 に 2022-12-28 10:03:24
dorioro No it doesn't it is just the silicon pad. Nothing else included.
2022-12-30 04:38:34 役に立つ (1)回答 (6)
Q: Is it possible to turn on/off lcd backlight programmatically via driver or any way?
尋ねた BartoszCelmer に 2019-11-22 05:17:21
dorioro I don’t believe you can control it but take a look at this Https learn.adafruit.com adafruit-pitft-3-dot-5-touch-screen-for-raspberry-pi backlight-control
2022-12-10 12:40:10 役に立つ (0)回答 (2)
Q: hello, Can i use or with an alfawise u20? thanks
尋ねた Nyan54 に 2020-06-30 12:32:14
dorioro If you can connect it to the mobo and change firmware accordingly, Yes
2022-12-10 12:36:25 役に立つ (0)回答 (3)
dorioro
20/10/2022
Q: What is max cutting diameter. In desciption it says 5mm on the handle it says 1mm
尋ねた Barry に 2020-05-02 11:40:03
dorioro Depends on what you cut. It has 5mm opening. But obviously you are limited by material type.
2022-10-19 05:47:04 役に立つ (0)回答 (18)
dorioro
05/10/2022
Q: What version of sensor do you provide ?
尋ねた Jacek Leonhard に 2019-04-23 05:12:26
dorioro I got v3.1
2022-09-20 01:32:57 役に立つ (0)回答 (2)
dorioro
20/09/2022
尋ねた daneelg に 2019-11-06 03:32:13
dorioro I found this tutorial for another model.
2022-08-20 02:34:56 役に立つ (0)回答 (6)
Q: What size fan does this case support?
尋ねた cben2142 に 2019-01-10 10:15:31
dorioro 30mm fan can be used
2022-08-20 02:32:10 役に立つ (0)回答 (4)
Q: hi it works with new ender 5? thanks
尋ねた lorenzoquadri31 に 2019-03-28 06:38:56
dorioro I installed it on Ender 5 Plus with splitter for Z axis motors and works fine once you configured it correctly.
2022-08-11 12:09:25 役に立つ (0)回答 (2)
Q: Does Ender 5 mainboard (marlin 1.0.1) work?
尋ねた Pápai に 2021-01-18 03:06:12
dorioro Depends on mobo version. In teory with proper firmware upgrade it should work
2022-07-19 02:41:36 役に立つ (0)回答 (2)
尋ねた zondaslight に 2019-06-10 09:54:20
dorioro You need to update firmware
2022-07-19 02:40:31 役に立つ (0)回答 (2)
尋ねた magnusxiii に 2022-07-18 04:51:31
dorioro It’s a direct replacement. But depending on your setup you might need to update firmware. For example if you have bltouch
2022-07-19 02:38:47 役に立つ (0)回答 (1)
dorioro
13/07/2022
dorioro
13/07/2022
dorioro You should wait for it to cool down before removing the printed part
2023-05-23 11:24:04 役に立つ (0)