This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

This motor appears very similar to a Hextronic motor sold by HK. It even has the same potential for failure as the HK Hextronic motor. The wire connection point or one of the winding wires will eventually break or short from movement near the back of the motor. The best way to prevent this is to disassemble the motor and remove both bearings. Use a piece of paper towel at both ends of the bearing tunnel to seal it up. Make up some 4 hour epoxy thinned about 20% to 30% with epoxy thinner. Use this thinned epoxy to dip the winding's until they are thoroughly coated and bonded together. Use some unthinned epoxy to prevent the three connection wires from moving between the heat shrink and motor winding's. Mechanically this makes the winding's more durable and electrically it improved heat dissipation. After the epoxy thoroughly cures, (24 hours) remove the paper towel plugs from both ends of the bearing tunnel and make sure that no epoxy entered the tunnel that will interfere with the re-installation of the bearings.

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

Articolo arrivato in sostituzione di uno difettoso. Tutto perfetto Grazie

良好な状態で受信

received with good condition

良好な状態で受信

記述通り

Just as described

記述通り

記述されたエンジン

motore come da descrizione

記述されたエンジン

たいへん良い

excellent

たいへん良い

予想通り、これはフェニックス1600の代替品でした

As expected, this was a replacement for a Phoenix 1600

予想通り、これはフェニックス1600の代替品でした

モーターは注文から2週間後、非常に迅速な配達を受けました。 まだテストされていません。 唯一の包装は非常に貧しかった - わずか2つの薄いビニール袋(バブル箔などなし)。

The motor received 2 weeks after ordering - very fast delivery. Not tested yet. Only packaging was quite poor - only two thin plastic bags (no bubble foil or so). Sp I trust the motor will be O.K. and working properly.

モーターは注文から2週間後、非常に迅速な配達を受けました。 まだテストされていません。 唯一の包装は非常に貧しかった - わずか2つの薄いビニール袋(バブル箔などなし)。

VERY GOOD

VERY GOOD

VERY GOOD

すごい

ottimo

すごい