The Kingkong FPV have very good Runcam FPV camera. Very good to fly. Many speed and power with 3S. Current my favorite. It have no DSHOT because it use a F3 PICO BLX. You can fix it if you move the Motor 1 to PPM and move the resource from PPM to the Motor 1. After that you can use DSHOT600. No Betaflight 3.2 available for now, for the PICO BLX. But no problem, I'm happy with the Kingkong FPV.

The Kingkong FPV have very good Runcam FPV camera. Very good to fly. Many speed and power with 3S. Current my favorite. It have no DSHOT because it use a F3 PICO BLX. You can fix it if you move the Motor 1 to PPM and move the resource from PPM to the Motor 1. After that you can use DSHOT600. No Betaflight 3.2 available for now, for the PICO BLX. But no problem, I'm happy with the Kingkong FPV.

The Kingkong FPV have very good Runcam FPV camera. Very good to fly. Many speed and power with 3S. Current my favorite. It have no DSHOT because it use a F3 PICO BLX. You can fix it if you move the Motor 1 to PPM and move the resource from PPM to the Motor 1. After that you can use DSHOT600. No Betaflight 3.2 available for now, for the PICO BLX. But no problem, I'm happy with the Kingkong FPV.

It's definitely the best micro quad I've ever had! Very silent, snappy and responsive even on 2S. Excellent FPV experience with Runcam and OSD, hovewer it does require some modifications to work properly. Here are some tips: a) Getting flysky FS-i6 failsafe to work: 1. Receiver: re-solder WHITE wire from pin 3 to 4 (ibus pin which is left unused) 2. Remove upper VTX module and re-solder same white wire from PPM to neighbour R3 pin on controller pcb. 3. Open Betaflight configurator and do the following steps: Ports > UART3 > turn on Serial Rx Configuration > Scroll down to Receiver tab > Receiver mode: Serial-based receiver (...), Serial Receiver Provider: IBUS 4. Save and Reboot. Enjoy trimming-free and noiseless IBUS with working failsafe (I wonder why they haven't set this up by default). b) Display correct voltage in OSD: Just solder the blue wire from Runcam to controller "5-18V" pin (most bottom left, next to GND black wire). c) You may need to calibrate motors input range by downloading BLHeli configurator. I think those instructions are not obvious and should be put in product description or FAQ. Additional observation: only two ESC support DSHOT, even after flashing to the latest BLHeli 16.7 firmware, which is pretty strange, however they're working fine with MULTISHOT as left by default.

It's definitely the best micro quad I've ever had! Very silent, snappy and responsive even on 2S. Excellent FPV experience with Runcam and OSD, hovewer it does require some modifications to work properly. Here are some tips: a) Getting flysky FS-i6 failsafe to work: 1. Receiver: re-solder WHITE wire from pin 3 to 4 (ibus pin which is left unused) 2. Remove upper VTX module and re-solder same white wire from PPM to neighbour R3 pin on controller pcb. 3. Open Betaflight configurator and do the following steps: Ports > UART3 > turn on Serial Rx Configuration > Scroll down to Receiver tab > Receiver mode: Serial-based receiver (...), Serial Receiver Provider: IBUS 4. Save and Reboot. Enjoy trimming-free and noiseless IBUS with working failsafe (I wonder why they haven't set this up by default). b) Display correct voltage in OSD: Just solder the blue wire from Runcam to controller "5-18V" pin (most bottom left, next to GND black wire). c) You may need to calibrate motors input range by downloading BLHeli configurator. I think those instructions are not obvious and should be put in product description or FAQ. Additional observation: only two ESC support DSHOT, even after flashing to the latest BLHeli 16.7 firmware, which is pretty strange, however they're working fine with MULTISHOT as left by default.

It's definitely the best micro quad I've ever had! Very silent, snappy and responsive even on 2S. Excellent FPV experience with Runcam and OSD, hovewer it does require some modifications to work properly. Here are some tips: a) Getting flysky FS-i6 failsafe to work: 1. Receiver: re-solder WHITE wire from pin 3 to 4 (ibus pin which is left unused) 2. Remove upper VTX module and re-solder same white wire from PPM to neighbour R3 pin on controller pcb. 3. Open Betaflight configurator and do the following steps: Ports > UART3 > turn on Serial Rx Configuration > Scroll down to Receiver tab > Receiver mode: Serial-based receiver (...), Serial Receiver Provider: IBUS 4. Save and Reboot. Enjoy trimming-free and noiseless IBUS with working failsafe (I wonder why they haven't set this up by default). b) Display correct voltage in OSD: Just solder the blue wire from Runcam to controller "5-18V" pin (most bottom left, next to GND black wire). c) You may need to calibrate motors input range by downloading BLHeli configurator. I think those instructions are not obvious and should be put in product description or FAQ. Additional observation: only two ESC support DSHOT, even after flashing to the latest BLHeli 16.7 firmware, which is pretty strange, however they're working fine with MULTISHOT as left by default.

Sehr schnelle Lieferung. Ist ein sehr guter Einteiger Copter. Schnelle Einrichtung in Betaflight. Gutes Flugverhalten. Bin sehr Zufrieden. Toller Copter zu einem guten Prei/Leistungsverhältnis. Vielen Dank an Das Bangood Team

Sehr schnelle Lieferung. Ist ein sehr guter Einteiger Copter. Schnelle Einrichtung in Betaflight. Gutes Flugverhalten. Bin sehr Zufrieden. Toller Copter zu einem guten Prei/Leistungsverhältnis. Vielen Dank an Das Bangood Team

Sehr schnelle Lieferung. Ist ein sehr guter Einteiger Copter. Schnelle Einrichtung in Betaflight. Gutes Flugverhalten. Bin sehr Zufrieden. Toller Copter zu einem guten Prei/Leistungsverhältnis. Vielen Dank an Das Bangood Team

tutto perfetto come da descrizione

tutto perfetto come da descrizione

tutto perfetto come da descrizione

Всё хорошо, но требует доработки - перепаять камеру (иначе не показывает напряждение питания) и перепаять flysky приёмник с ppm на s(i)bus.

Всё хорошо, но требует доработки - перепаять камеру (иначе не показывает напряждение питания) и перепаять flysky приёмник с ppm на s(i)bus.

Всё хорошо, но требует доработки - перепаять камеру (иначе не показывает напряждение питания) и перепаять flysky приёмник с ppm на s(i)bus.

This is by far one of the best micros out there fly well right out the box. Feels well built

This is by far one of the best micros out there fly well right out the box. Feels well built

This is by far one of the best micros out there fly well right out the box. Feels well built

très bien comme dans le descriptif de ampli et livraison très rapide merci banggood

très bien comme dans le descriptif de ampli et livraison très rapide merci banggood

très bien comme dans le descriptif de ampli et livraison très rapide merci banggood

отличный квад до Москвы 2.5 недели! Перепаял красный провод камеры на 5 v и синий на v bat чтобы показывал правильно osd батареи также перепаял с ppm на ibus для работы фэйлсейва. Пришел в новой версией с радиатором охлаждения расположенным на видео передатчике.

отличный квад до Москвы 2.5 недели! Перепаял красный провод камеры на 5 v и синий на v bat чтобы показывал правильно osd батареи также перепаял с ppm на ibus для работы фэйлсейва. Пришел в новой версией с радиатором охлаждения расположенным на видео передатчике.

отличный квад до Москвы 2.5 недели! Перепаял красный провод камеры на 5 v и синий на v bat чтобы показывал правильно osd батареи также перепаял с ppm на ibus для работы фэйлсейва. Пришел в новой версией с радиатором охлаждения расположенным на видео передатчике.

Superb small 2s drone. So smooth and quiet. I got the Flysky version. Very good range good camera and easy to fly. Very good to learn acro with for a begginer .

Superb small 2s drone. So smooth and quiet. I got the Flysky version. Very good range good camera and easy to fly. Very good to learn acro with for a begginer .

Superb small 2s drone. So smooth and quiet. I got the Flysky version. Very good range good camera and easy to fly. Very good to learn acro with for a begginer .

Concerns last delivery Fly EGG after the first battery plugging in, two out of four esc are no longer working properly and the smell is burnt. Similarly, in the FPV Cam, the ring is over-twisted to counter the lens please clarify

Concerns last delivery Fly EGG after the first battery plugging in, two out of four esc are no longer working properly and the smell is burnt. Similarly, in the FPV Cam, the ring is over-twisted to counter the lens please clarify

Concerns last delivery Fly EGG after the first battery plugging in, two out of four esc are no longer working properly and the smell is burnt. Similarly, in the FPV Cam, the ring is over-twisted to counter the lens please clarify