Olcsó, jó minőségű tápegység!

Olcsó, jó minőségű tápegység!

Olcsó, jó minőségű tápegység!

Itś a good an smal power supply

Itś a good an smal power supply

Itś a good an smal power supply

キャンパクトと強力なAC/DC

Campact and powerful AC/DC

キャンパクトと強力なAC/DC

動作

It works

動作

Not instant on like many of the switching supplies, this one seems to power up to the full 24V in about a second. So no big in rush of voltage. The PCB was excellent, no solder splashes or sloppy wiring, components all properly mounted. All in all, a very nice assembly job.

Not instant on like many of the switching supplies, this one seems to power up to the full 24V in about a second. So no big in rush of voltage. The PCB was excellent, no solder splashes or sloppy wiring, components all properly mounted. All in all, a very nice assembly job.

Not instant on like many of the switching supplies, this one seems to power up to the full 24V in about a second. So no big in rush of voltage. The PCB was excellent, no solder splashes or sloppy wiring, components all properly mounted. All in all, a very nice assembly job.

Fine quality for low price. I use it for some time now without problems Starts nice and slow without big inrush current

Fine quality for low price. I use it for some time now without problems Starts nice and slow without big inrush current

Fine quality for low price. I use it for some time now without problems Starts nice and slow without big inrush current

Reçu rapidement et bien emballé j en suis vraiment très content et surpris de la qualité je l utilise pour un moteur et c'est impeccable je le recommande ainsi que tout le site banggood qui est très professionnels

Reçu rapidement et bien emballé j en suis vraiment très content et surpris de la qualité je l utilise pour un moteur et c'est impeccable je le recommande ainsi que tout le site banggood qui est très professionnels

Reçu rapidement et bien emballé j en suis vraiment très content et surpris de la qualité je l utilise pour un moteur et c'est impeccable je le recommande ainsi que tout le site banggood qui est très professionnels

As with most of these supplies the first I do is disassemble them to make sure there's no solder blobs or bad connections. No way I assume they are perfect and just plug them in. Thus I wasn't surprised when I found that the J1 jumper had been repaired because it was obvious from the burn mark on the component side of the PCB that there was a problem with the circuitry. The problem had also obviously required a fuse replacement since it was cooked in that area as well. The issue with the repair was they didn't actually replace the jumper at J1, they just bridged the gap with solder. Because it's cheap, quick and they could care less about your safety or quality of their products. Once I fixed it properly with a jumper, I found it takes about 2 seconds from a cold start before the supply kicks in. Voltage is stable. As the old adage goes, you pay your money, you take your chances.

As with most of these supplies the first I do is disassemble them to make sure there's no solder blobs or bad connections. No way I assume they are perfect and just plug them in. Thus I wasn't surprised when I found that the J1 jumper had been repaired because it was obvious from the burn mark on the component side of the PCB that there was a problem with the circuitry. The problem had also obviously required a fuse replacement since it was cooked in that area as well. The issue with the repair was they didn't actually replace the jumper at J1, they just bridged the gap with solder. Because it's cheap, quick and they could care less about your safety or quality of their products. Once I fixed it properly with a jumper, I found it takes about 2 seconds from a cold start before the supply kicks in. Voltage is stable. As the old adage goes, you pay your money, you take your chances.

As with most of these supplies the first I do is disassemble them to make sure there's no solder blobs or bad connections. No way I assume they are perfect and just plug them in. Thus I wasn't surprised when I found that the J1 jumper had been repaired because it was obvious from the burn mark on the component side of the PCB that there was a problem with the circuitry. The problem had also obviously required a fuse replacement since it was cooked in that area as well. The issue with the repair was they didn't actually replace the jumper at J1, they just bridged the gap with solder. Because it's cheap, quick and they could care less about your safety or quality of their products. Once I fixed it properly with a jumper, I found it takes about 2 seconds from a cold start before the supply kicks in. Voltage is stable. As the old adage goes, you pay your money, you take your chances.