お客様レビュー

レビューを書きます。
  • すべてのレビュー (7508)
  • 画像 (930)
  • ビデオ (12)
  • オールスター
    • オールスター(7508)
    • 5スター(7265)
    • 4スター(185)
    • 3スター(22)
    • 2スター(14)
    • 1スター(22)
並び替え:
トップレビュー
  • トップレビュー
  • 最も役立つ
  • 新着商品
あなたの国からのレビューのみ(Japan)
|
オリジナルを表示

レビューの一部は自動翻訳されています。

  • 27/08/2014

    The cheapest way to get the Nano v.3. USB cable is the standard one. I had problems recognizing in W7-x64 but it works perfect after installing new driver (different of Ardudino Uno), Can download from http://robotstore.cz/obchod/arduino/dccduino-nano-v3-0-atmega328-ch340g-arduino-rozsirujici-deska/

    コメント (1)
    オリジナルを表示
  • 02/08/2019

    Works great. Used in project to run a OLED screen. You need to install CH340 drivers and select "old bootloader" in Arduino IDE in order for it to conect. Price unbeatable.

    コメント (1)
    オリジナルを表示
  • 12/02/2020

    優れた製品 優れた製品 優れた経験 優れた経験 この製品は古いポットローダーによって駆動されています この製品は使用しています(古いブートローダ)

    コメント
    オリジナルを表示
  • 26/02/2018

    This is really nice board. Silkscreen is readable. Only complaint I have is that board has mini usb instead of micro usb connector, so you might need to get cable for it: http://bit.ly/2oj7ZeB You will have to solder pins yourself, if you’re not into it, there is board with pins already soldered: http://bit.ly/2oeN5gH

    コメント
    オリジナルを表示
  • 03/12/2017

    This is quite nice board. Silkscreen is nice and readable. Only complaint I have is that board has mini usb instead of micro usb connector, so you might need to get mini usb cable: https://goo.gl/MgE41a You will have to solder pins yourself, if you’re not into it, there is board with pins already soldered: https://goo.gl/PYEipY

    コメント
    オリジナルを表示
  • 23/11/2014

    Incredible price for this small device. But with the normal ftdi-drivers this nano wasn't recognized and installed properly (Win 7 64bit). With the following drivers the problems were fixed. Now the clone runs absolutely flawless like an original one. Drivers: http://www.winchiphead.com/download/CH341/CH341SER.ZIP

    コメント
    オリジナルを表示
  • 01/10/2018

    Nice little controller for HAM radio fox-hunting transmitter on 80-meters. Have built the transmitter board and the Arduino Nano is piggy backed upon it. Arduino takes care of the timing (transmitter on and off) and generates the Morse code to be transmitted. Five of these units are operational at this time, more to follow!

    コメント
    オリジナルを表示
  • 25/01/2021

    すでにそうであるように、すべてのアデュイノは完璧な状態で動作しています。 すでにプログラムされており、使用の準備が整いました。 使用するケーブルに注意してください、正常に動作しないケーブルがあります、それはarduinoからではありません。 ナノの「古いブートローダ」を使う。

    コメント
    オリジナルを表示
  • 07/08/2017

    This is quite nice board. I tested it on my mac, and it worked like a charm. Silkscreen is more readable than on some other nano boards I have. Only complaint I have is that board has mini usb instead of micro usb connector, which is far less common, so you might need to get mini usb cable: https://goo.gl/MgE41a. You will have to solder pins yourself, if you’re not into it, there is board with pins pre soldered: https://goo.gl/PYEipY

    コメント
    オリジナルを表示
  • 20/10/2019

    Operational only with old bootloader (in Arduino IDE)!

    コメント (1)
    オリジナルを表示
Show:

    合計 0 ページ

    ページに移動

    あなたにおすすめの商品

    recommendation for you
    • US$9.99
    • US$7.99
    • US$8.99
    • US$4.99
    • US$10.99
    • US$12.99
    • US$7.35
    • US$9.99
    • US$9.99
    • US$5.99
    • US$61.41
    • US$33.62
    • US$36.99
    • US$9.11
    • US$41.25
    • US$21.99
    • US$8.99
    • US$17.71