非常に優れた飛行コントローラー!

Very good flight controller!

非常に優れた飛行コントローラー!

良さそうだ。

Looks good quality.

良さそうだ。

良く見える まだ試してない 早送りだ ありがとう。

Looks good. Not tried yet. Fast shipping. Thanks.

良く見える まだ試してない 早送りだ ありがとう。

ブラックボックス用のバロとフラッシュを追加した素敵なFC、多くのUartが利用可能で、はんだ付け前にワイヤをねじ込むためにPCBに必須の穴が付属しているので、配線が簡単になります。 TX5にはGPS専用のピンアウトがあり、キャディックス/DJIエアユニットも使用できます。 非常に小さなレプリカピンアウトPCBも送信され、ラベル付けされたすべてのピンの両方が有用であり、後でまともなキーリングを追加することができます。 これまでのところ2つを使用しており、基本的なチロローエンドfcをはるかに良いものに置き換えるために別のものを購入するでしょう。 唯一の失望は、私がまだこれのために見ることができるINAVファームウェアは、それは非常に完全な小さな仲間になります! ねじ込み用の穴が開いた jemchu(?) 20 esc ボードに叫ぶ必要があります

Nice FC with addition of baro and flash for blackbox, lots of uarts available and essential holes in PCB to thread wires before soldering which makes it sooooo much easier to get wired up. Has a dedicated pin out on TX5 for GPS and works with Caddix/DJI air unit as well. Great little replica pin out PCB sent as well with all pins labelled that's both useful and make a decent keyring addition afterwards. Have used two so far and will likely buy another to replace basic tyro low end fcs with something much, much better. Only disappointment is no INAV firmware I can see for this yet which would make it a very complete little fellow! Also have to give a shout out to jemchu(?) 20 esc board with same holes for wire threading

ブラックボックス用のバロとフラッシュを追加した素敵なFC、多くのUartが利用可能で、はんだ付け前にワイヤをねじ込むためにPCBに必須の穴が付属しているので、配線が簡単になります。 TX5にはGPS専用のピンアウトがあり、キャディックス/DJIエアユニットも使用できます。 非常に小さなレプリカピンアウトPCBも送信され、ラベル付けされたすべてのピンの両方が有用であり、後でまともなキーリングを追加することができます。 これまでのところ2つを使用しており、基本的なチロローエンドfcをはるかに良いものに置き換えるために別のものを購入するでしょう。 唯一の失望は、私がまだこれのために見ることができるINAVファームウェアは、それは非常に完全な小さな仲間になります! ねじ込み用の穴が開いた jemchu(?) 20 esc ボードに叫ぶ必要があります

schnell geliefert, gute Qualität.

schnell geliefert, gute Qualität.

schnell geliefert, gute Qualität.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

This could be the best flight controller,, but... 1) The BOOT button did not work for me (The device was not even listing in the devices in windows) -I have investigated this and fiound out that the button must pull BOOT0 pin of the MCU to VDD, but when the FC is connected to the usb, there is no 3.3v on the other side of the button. 2) There is no INAV build for this FC. -I have tried the one for MATEKF405-SE and it bricked my Baro. (Actually, the rest was working not sure if UARTS are in the right order as on PCB) 3) After I have reflashed to BF, the baro is not working anymore. 4) The support chat of the facebook group of SKYSTARS answers to do the things that i have already did despite that i have descrbed the problem and I am not a total newbie. 5) SKYSTARS website downloads page leads to nowhere so they even not giving pin definitions or a complete BF build for the FC. Overall it is very very very good quality soldered pcb, it is nice and tiny, it has baro and many uarts. It could have been the best flight controller for the price.

10ボルトベックの素晴らしい小さなFCは、ラッシュタンクミニで非常に役立ちます。 VTX のノイズを非常にきれいにします。 超幸せだ。

What an awesome little FC the 10volt bec is very helpful with the Rush tank mini. Very clean no noise on the VTX. Super happy.

10ボルトベックの素晴らしい小さなFCは、ラッシュタンクミニで非常に役立ちます。 VTX のノイズを非常にきれいにします。 超幸せだ。