招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
尋ねた Chandra に 2020-09-30 12:08:29
Goober it’s neither, really. but closer to the V4 than the V5. But there are numerous issues - the biggest being that the arms are 5mm not 6mm as he original build spec demands. It’s a big build that’s meant to swing 7” props - 6mm arms is important, i think.
2020-09-30 08:00:55 役に立つ (4)回答 (1)
尋ねた Goober に 2020-04-29 07:36:52
RcCharly I plugged in balance leads backwards like 100 times, works like a charm.
2020-04-30 04:52:53 役に立つ (1)回答 (1)
Q: Any LED pin available? Pin for smart audio or other uart?
尋ねた MilanSpacek に 2019-01-13 03:33:56
Goober yeahhhhhhhh this board died on my too within a few packs. smoked a motor too - the fets don’t seem rated either for the voltage or the amps. i was using 2s and 0802 12000kv 40mm props. should’ve been TOTALLY fine.
2019-02-03 11:13:17 役に立つ (0)回答 (1)
Q: Can anyone answer the buzzer pad question? It's a deal breaker for me if there isn't one.
尋ねた Glenn Vorhes に 2019-01-25 09:37:16
Goober doesn’t have a buzzer pad - but dshot beacon should work if that’s loud enough.
2019-02-02 12:21:15 役に立つ (0)回答 (1)
Q: What board do I pick when flashing Betaflight?
尋ねた Jim Morrison に 2019-01-12 01:47:45
Goober Mine says the target is "NOX"
2019-01-28 04:20:55 役に立つ (0)回答 (4)
尋ねた Aaron に 2019-01-07 06:06:22
Goober All the pads are labeled though... across the top: GND, 5V, VOUT, VIN across the bottom 3V, (DSM, etc), SBUS, 5V, GND. Page says RX2 for RC control. So.. no TX, No buzzer, No SA... which is pretty silly. But it’s 25% the cost of others. so priorities, i guess.
2019-01-20 07:04:57 役に立つ (0)回答 (3)
Q: they could DO IT BETTER!!! add current pin instead of Ground pin near leds out!
尋ねた frimen に 2019-01-07 05:51:04
Goober current!? what is this ancient analogue technology you speak of?? Get with the times and get an ESC that supports telemetry. I’m really kidding though - you bring up a great point. regardless this would be a HARD PASS for me. ICM gyro on a micro sized FC with no integrated softmounts? We kinda ran this experiment already the wave of ICM gyro equipped FC that were universally panned as being impossible to tune without integrated soft mounts / grommets.
2019-01-07 07:10:43 役に立つ (0)回答 (3)
Q: Will you be selling the frame and spare parts separately?
尋ねた Goober に 2018-11-15 06:51:17
Conciliabule Yes, will sell the empty frame next week
2018-11-27 03:57:30 役に立つ (0)回答 (1)
Q: are you supposed to be able to snap off the two long legs? is that what the dotted lines are for?
尋ねた Goober に 2018-10-16 08:02:10
Marconius Haaaaaaaaaa!!!!!!!!!!!
2018-10-30 03:08:57 役に立つ (0)回答 (1)
Goober It's a Blheli_S ESC - BLHELI_32 should not work. Sounds like you might have the buzzer configured wrong.
garrigueta
03/07/2018
0
コメント (2)
尋ねた Goober に 2018-08-23 07:59:42
enagano I would like to know if the original alien pdb will work?
2018-09-03 06:26:49 役に立つ (0)回答 (2)
Q: what does the buck boost do exactly?
尋ねた nonickjustname に 2018-07-20 09:22:03
Goober Buck boost is a type of voltage regulator. Buck boost regulators are usually much more reliable than the alternative, which is a linear regulator (they’re usually cheaper). I’ve heard that the regulator on this board though is best suited to ~25mw VTX’s. If you’re going to run ~200mw you may need a separate regulator. Just what I’ve heard. No experience personally.
2018-08-10 10:14:43 役に立つ (1)回答 (4)
Q: How can the 6" be 3g lighter then the 5"?
尋ねた Emil79 に 2018-06-23 03:43:40
Goober looks like they weighed it without the PDB and accessories - for the 5” this was all included in the weight
2018-07-01 02:15:20 役に立つ (0)回答 (1)
Q: Planned release date? This looks amazing!
尋ねた Goober に 2018-01-25 07:06:02
Lanny Hello, it is expected to be stock at the beginning of March.
2018-02-05 03:47:08 役に立つ (0)回答 (1)
尋ねた Grudge に 2017-11-29 12:57:31
Goober The images shown here are not of the actual product. They are of the product that is being cloned by PUDA. You can see those image on the original manufacture's site: https://xhover.com/products/xhover-stingy-pre-order FWIW the PUDA is available elsewhere, it likely has press nuts (not embedded nuts), the reinforced plate for the cam may or may not come with it, the hardware will almost definitely NOT be titanium. etc... etc...
2017-12-02 10:05:00 役に立つ (2)回答 (4)
Goober The GEPRC Crocodile Baby 4 Analog appears to come with the Caddx Ratel, which is 19mm cam - the Ratel 2 is the same width - so it really should fit just fine.
2021-03-04 09:24:27 役に立つ (3)