すべてのメッセージ

Q: is spectre DX5 compatible?

尋ねた roberto51it に 2020-04-06 05:26:14

Deegeetee No, think you find it runs the FlySky protocol

2020-09-21 03:13:00 役に立つ (0)
提出
回答 (1)

Q: Is there an esc for coreless motor?

尋ねた popeye に 2020-04-15 10:50:18

Deegeetee Yes, it's built into the board already

2020-09-21 03:12:09 役に立つ (0)
提出
回答 (1)

Q: is this compatible with the Flysky Fs i6 and goggles Skyzone 2x?

尋ねた johnbos に 2020-09-16 02:16:22

Deegeetee Buy the version with the FlySky receiver & it'll be compatible with any FlySky or Turnigy transmitter, running either Protocol: AFHDS and AFHDS-2A (Switchable between both protocols). It will give you either 8 or 14 channels, as follows: Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) I would imagine that it's also compatible with most goggles.

2020-09-17 05:56:39 役に立つ (0)
提出
回答 (5)
Deegeetee 2020-08-01 10:17:05
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Q: Does it use ailerons?

尋ねた BG471416232 に 2020-07-27 06:39:56

Deegeetee Yes it does but the servos are built into the inside of the fuselage, with an external control arm on each side of the fuselage, which locates into a bracket on the end of each aileron when the wings are plugged in.

2020-07-27 04:26:12 役に立つ (0)
提出
回答 (1)

Q: can i connect it with a taranis frysky Q X7 Transmitter??

尋ねた BG421541494 に 2020-07-15 04:42:43

Deegeetee There are two versions with Frsky receivers, one for EU based flyers and one for non EU based flyers.

2020-07-15 07:46:31 役に立つ (0)
提出
回答 (2)

Deegeetee I personally have no experience of trying to use another transmitter, other than the supplied one. However I have seen an answer in the Q

2020-02-17 10:15:07 役に立つ (0)
提出
回答 (1)

Q: Mode 1 ou 2 ?

尋ねた ventilo76 に 2019-09-17 01:17:32

Deegeetee This transmitter comes in Mode 2 but can easily be switched to mode 1. On the back of the transmitter, you will find two small rubber inserts, which should have screws undernweath to change the set up from Mode 2 to Mode 1 or visa versa. There are also videos on YouTube that shows the process, which is extremely simple. In fact it\'s no more than tightening two screws and loosening two on the opposite side of the transmitter back. Just search YouTube for HOW TO: Change XK Transmitter from Mode 2 to Mode 1 (it\'s an x6 transmitter but the process is the same for this transmitter (X8)

2019-12-16 07:50:21 役に立つ (1)
提出
回答 (3)

Q: hi, or can we find the options of the model?

尋ねた donot に 2019-10-31 08:05:59

Deegeetee This transmitter comes in Mode 2 but can easily be switched to mode 1. On the back of the transmitter, you will find two small rubber inserts, which should have screws undernweath to change the set up from Mode 2 to Mode 1 or visa versa. There are also videos on YouTube that shows the process, which is extremely simple. In fact it's no more than tightening two screws and loosening two on the opposite side of the transmitter back. Just search YouTube for HOW TO: Change XK Transmitter from Mode 2 to Mode 1 (it's an x6 transmitter but the process is the same for this transmitter (X8)

2019-12-16 07:48:23 役に立つ (2)
提出
回答 (2)
Deegeetee 2019-07-20 07:21:23
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Deegeetee If your new transmitter uses the AFHDS 2A protocol, as you say, then this receiver will work with it. It will not work with the original Turnigy 9x, which uses AFHDS only

2019-07-30 10:01:29 役に立つ (2)
提出
回答 (2)
Deegeetee 2019-07-20 07:24:42
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Deegeetee 2019-07-20 07:23:23
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Deegeetee 2019-07-20 07:20:15
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Deegeetee 2018-10-08 10:01:33
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー:

Deegeetee 2018-10-08 10:01:33
0
推奨事項
コメント (0)

あなたが好きかもしれないトップレビュアー: