招待メールを購読することを心から歓迎します！
購読すると、製品に関する質問に答えるために電子メールで招待されます。購読すると、「役立つバッジ」も獲得できます。プライバシー設定ページでいつでも登録を解除できます。
他の人を助け、幸せになりましょう！
すべてのメッセージ
Q: Hello, does the Armory 7 come with Android 9 or Android 10 ? Thank you.
尋ねた Frangop に 2022-01-21 07:08:08
回答 (3)
尋ねた BG572139574 に 2021-09-28 09:00:24
gdaelen armor 7 is 8Gb RAM (android10 ) , armor 7E is 4Gb RAM (android9) , this is armor 7
2021-09-29 01:20:18 役に立つ (0)回答 (4)
gdaelen
14/05/2021
尋ねた gdaelen に 2020-12-03 07:06:59
CarpolQuirky thanks for your feedback.
2020-12-14 01:53:41 役に立つ (0)回答 (1)
Q: Is this a reversing solenoid. Is there a wiring diagram?
尋ねた gdaelen に 2019-02-17 10:21:43
Shallop you can find the top right corner "Help" to chat live with online customer service.
2019-03-03 09:36:06 役に立つ (1)回答 (2)
gdaelen
15/05/2020
尋ねた gdaelen に 2020-04-24 03:09:26
Flash there is no schematic support
2020-05-03 10:24:08 役に立つ (1)回答 (1)
gdaelen
12/03/2020
Q: When I plugged in the 24-pin ATX PSU, no voltages were shown on the PCB terminals. What is missing?
尋ねた hcemc に 2019-12-27 02:06:53
gdaelen some power supplies need at least a small load to remain "on" , otherwise it start and stop immediately.
2020-03-11 11:31:09 役に立つ (1)回答 (8)
gdaelen
29/01/2020
gdaelen
22/01/2020
gdaelen
22/01/2020
Q: only english ? no other language ??????
尋ねた gdaelen に 2019-12-30 07:34:22
Hyenad This smart watch support English and other common language.
2020-01-03 12:02:23 役に立つ (0)回答 (1)
gdaelen
02/04/2019
Q: is it possible to have schematic ?
尋ねた gdaelen に 2019-04-02 05:35:36
json check the descriptions please
2019-04-07 12:59:49 役に立つ (0)回答 (1)
Q: i lost manual , whre can i download it ? thanks
尋ねた gdaelen に 2018-11-08 08:36:52
Scottybman Offing Maybe you can use the contact us to contact the banggood customer service team.
2018-11-22 02:45:29 役に立つ (0)回答 (1)
gdaelen
25/08/2018
gdaelen on the back side , above "D6" , there is two caps and then a 390k resistor.this one is between 3.3v and Vdd of oled !!!!!!!!!!!!replace it with a wire and it will boot at power onthe pin near the side of board of "prg" button need to be connected to ground (the usb ground is very close)schematic is partially wrong , serigraph is ok but sba=sda(i2c)=D4 ,a8=a0 (analog) , SCL=clk(i2c)=D5=GPIO14.reset of oled is D2(GPIO4).
roberto_33
09/03/2018
0
コメント (2)
gdaelen
27/04/2018
gdaelen it is Android 10 .
2022-01-22 01:35:42 役に立つ (1)