お客様レビュー

レビューを書きます。
  • すべてのレビュー (49)
  • 画像 (7)
  • ビデオ (0)
  • オールスター
    • オールスター(49)
    • 5スター(44)
    • 4スター(5)
    • 3スター(0)
    • 2スター(0)
    • 1スター(0)
並び替え:
トップレビュー
  • トップレビュー
  • 最も役立つ
  • 新着商品
あなたの国からのレビューのみ(Japan)
|
オリジナルを表示

レビューの一部は自動翻訳されています。

  • shawnz
    US
    30/11/2016

    First off there were no instructions whatsoever in the frame kit. I assembled it by looking at the pictures on the Banggood site. I'm currently not able to complete the assembly because the flat plate doesn't fit into the 'L' brackets. This is nothing a little sandpaper or a file won't cure. The FPV camera verticle pieces are a tight squeeze put they pop into the top plate with just the right bit of force. These plates don't actually secure to the frame other than their friction fit. The horizontal posts / bottom plate of the gopro mount and of course the FPV camera keep the vertical pieces pinned in the top plate with the very bottom going into a slot in the bottom plate. The frame includes a Carbon fiber battery protector plate (not in the pictures) for the underslung battery. I'm replacing the included PDB with a Realacc HUBOSD 'X-type' for OSD and PDB. The LED board is included (see my tail light pic) I'll be building this up as a racer and I'm hoping for some longevity. I don't expect this to be an especially tough bird with only 4 standoffs but when you have such a small center section, what can you do? The hardware seems decent so far and the screw lengths are good. I love how light weight it is!

    コメント (2)
    オリジナルを表示
  • 22/04/2017

    This frame came with a lot of goodies like the LED board and PDB which is cool. The GoPro mount is cool and the tiered arm style leads to way less propwash and overall turbulence when flying in general. Ultimately, some problem I ran into were: - There is not enough vertical height to stack 3 board with the stock standoffs included with my 4-in-one ESC board, OMNIBUS flight controller, and this frame; the standoffs had to be cut the clear the top of the frame. So, with ESCs and FC, there is no room for the PDB unless you get shorter spacers. - The width of the FPV camera area is not compatible with the Foxeer Monster (V1/V2), because the width of the camera is too small for the included screws to reach (the screws included with the camera were too short to even make it through the carbon thickness). We ended up using longer custom screws and washers to make it work, see included pic. Nothing wrong with the frame, just a compatibility thing to keep in mind with any similar cameras. - The cutouts for the FPV camera don't work with the Foxeer Monster V2, because the arc made to adjust the angle just doesn't line up at all with the camera holes; again, nothing wrong with the frame, just something to keep in mind. - The included LED board caused some very whacky issues with the quad. Wiring to 5V output on the flight controller led to the flight controller beeping erratically and the LEDs being dimmed, and not being able to arm the quad until the LED was removed. Not a big deal for me, I discarded the board, it's just an extra included so I wasn't really bothered. - The vertical plates of the GoPro mounting points which "notch" into the top part of the frame needed to be slightly sanded down and tapped with a hammer in order to fit into the slot; probably just a tolerance thing, no big deal. Overall it's a great frame, with a unique design. The arms are super thick and I haven't had any problems with bending or breaking, even after some HARD crashes. I wouldn't recommend it as a beginner build, because the way the whole thing is put together makes initial construction, wire management, and servicing pretty difficult; there's not a lot of room leftover and we had to make some custom adjustments (read: power tools and other hardware) to get everything to work well.

    コメント (1)
    オリジナルを表示
  • 27/05/2017

    The frame itself is quite tight. So because i did not have a 5V regulator handy I had to fit 3,5 tiers into one stack (the ,5 is the receiver). And that required some customization. I ended up using a one tall M3 bolt for each of the four stack corners along with various spacers to save as much space as was needed. The two front bots had to be cut down to fit under the FPV Camera angle mount. https://youtu.be/TRk6mpQN9lg Took a while to get it all sorted, but it flies fine now :) Wold recommend for a AIO Build Would NOT recommend to a new builder, if you're not going for AIO. Overall the frame feels much nicer that the Eachine Falcon 250 that was previously carrying the same setup. I did notice the lower center of gravity that caused more 'pendelum' effect that I was used to with a top-mounted battery. Build notes: sand, file or grind the sharp cut edges on the frame before you start building ;) Frame: Realacc-Phoenix-X210S (https://www.banggood.com/Realacc-Phoenix-X210S-210mm-3K-Carbon-Fiber-FPV-Racing-Frame-4mm-Frame-Arm-w-LED-Board-5V-12V-PDB-p-1104841.html) PDB: MATEK XT60 PDB W/ 5V & 12V BEC ESC: SUNRISE CICADA 20A BLHELI_S 4-IN-1 ESC BB2 (V.2) Motors: PURPLE CAP 2205 2600KV Receiver: Flysky X6B 2.4G 6CH VTX: Eachine TX526 5.8G 40CH 25MW/200MW/600MW Props: Kingkong 5040 5x4x3 Antenna: Aomway 5.8GHz FPV 4 Leaf Clover AV Transmission RHCP Transmitter: FlySky FS-i6

    コメント (1)
    オリジナルを表示
  • SegVIP2
    GB
    03/05/2017

    I really like this frame. Tricky to put together with all components for a noob, but got there. No instructions came with the package, but I knew this based on other reviews. It wasn't hard to work out where everything went. Would definately recommend.

    コメント
    オリジナルを表示
  • 04/12/2016

    Great Frame very happy with it ! Pros: This 4MM top and bottom plate !! PDB included. 3K Carbon. Cons: Edges by wire and battery strap are not beveled. No Instructions !!

    コメント
    オリジナルを表示
  • 08/07/2017

    Produit conforme a la description du site.Reçu dans une boite carton qui protège fort bien l'ensemble. Carbone de bonne qualité en 4mm d' épaisseur, Frame très bien découpée. Tout est fourni , vis , PCB et sangle de batterie.Chez Realacc , ils n'ont pas été radin,il y a beaucoup plus de vis que prévu. Seul bémol , il manque une notice de montage mais grâce aux photos de Bang good présentant en image la Frame , j ai pu l' assembler facilement. Je la recommande pour sa qualité, pour les sensations de vol , je n ai pas encore essayé

    コメント
    オリジナルを表示
  • 15/02/2017

    Just reveiced my package and lo and behold, they've sent me the wrong frame, haha :D I got a normal x210, instead of Phoeinx x210S. which I realy don't mind, because after I already ordered this frame, I got second toughts if this frame is really that strong. If you think, 4 standofs hold the two main plates together, I wouldn't trust that. So I'm actually happy that I got the "normal" x210. Hilariuos.

    コメント
    オリジナルを表示
  • 15/02/2017

    Carbon dust all over it but other then that it seems good. Havent had any major crashes with it yet but Im expecting it to hold up with it being 4mm

    コメント
    オリジナルを表示
  • 10/02/2017

    there's no instructions but anyone with half a brain should be able to put six pieces of carbon together. it's a great frame and super sturdy. I would not recommend for somebody's first build not much extra room inside

    コメント
    オリジナルを表示
  • 19/01/2017

    It's the best frame ever. It looks cool and is very stable.

    コメント
    オリジナルを表示
Show:

    合計 0 ページ

    ページに移動

    あなたにおすすめの商品

    recommendation for you
    • US$30.99
    • US$98.99
    • US$10.99
    • US$78.99
    • US$33.99
    • US$7.99
    • US$15.99
    • US$67.99
    • US$6.99
    • US$69.99
    • US$62.99
    • US$9.99
    • US$42.99
    • US$5.99
    • US$43.50
    • US$37.99
    • US$89.99
    • US$61.99