お客様レビュー

4.92 から 5
レビューを書きます。
  • すべてのレビュー (48)
  • 画像 (8)
  • ビデオ (0)
  • オールスター
    • オールスター(48)
    • 5スター(45)
    • 4スター(2)
    • 3スター(1)
    • 2スター(0)
    • 1スター(0)
並び替え:
トップレビュー
  • トップレビュー
  • 最も役立つ
  • 新着商品
あなたの国からのレビューのみ(Japan)
  • December-16 2020 10:13:27

    datasheet in some aspects misleading. Finally I got it working. It now shows reasonable results. Quality looks good.

    コメント (1)
  • March-20 2020 06:19:10

    Bien reçu ce jour sans casse. Reste à tester.

    コメント
  • February-27 2017 15:36:13

    Hi All, It can be hooked up to a simple usb/serial converter (only 4 wires required). Make sure the data lines (Tx and Rx) use 3V signalling. Running a simple powershell script the data is displayed. Script: [Byte[]] $request = 0xff, 1, 0x86, 0, 0, 0, 0, 0, 0x79 [Byte[]] $res = 0, 0, 0, 0, 0, 0, 0, 0, 0 $port = new-Object System.IO.Ports.SerialPort COM57,9600,None,8,one $port.Open() $port.Write($request, 0, 9) Start-Sleep -Milliseconds 50 For ( $i = 0; $i -lt 9; $i++ ) { $res[$i] = $port.ReadByte() } Write-Host

    コメント
  • July-08 2017 03:20:24

    Seems to do what it says on the box. Inside with a gas heater (with flue) on I got (with the script above, cheers) an uncomfortably high reading >1200ppm so I took it outside and got 385ppm after a few minutes, which seems right. So I have a window open now :-)

    コメント
  • January-17 2017 11:25:44

    Works as specified, worm up phase is longer than 3 minutes, but under 5 min. Supplycurrent is quit high with peaks, but on average also as specified.

    コメント
  • February-28 2018 16:32:37

    it arrived in 2 weeks, in a good packaging. It works well. good deal.

    コメント (2)
  • October-09 2019 06:49:13

    Veio jogado dentro do pacote, sem proteção. Mas chegou ok. Não testei ainda.

    コメント
  • April-01 2019 12:23:43

    хороший товар

    コメント
  • December-31 2020 21:02:20

    Works very well, but the one I got has an internal thermometer that's off by around 6 Kelvin. This makes all measurements wrong, and I had to implement a 3-point (at least) calibration using a linear function of temperature and measured CO2 ppm. The good news is, the error is linear in those 2 variables, so 3 accurately measured calibration points with a reference sensor will do the job. Another good news is that the sensor actually reports its measured temperature along with the ppm number via UART. I

    コメント (1)
  • June-24 2020 09:17:20

    CO2 measurements is very good. No calibration needed. I wired it to a nodemcu with Tasmota firmware flashed. Taslota also shows the temperature but this value is way off, 17 degrees C higher than the actual temperature. Strange since this offset is identical over the full range (can be used if the offset is compensated in sw). The temperature is only with a 1 degree resolution (not 0.1).

    コメント
Show:

    Total 0 pages

    Go to page

    Go

    あなたにおすすめの商品

    recommendation for you
    • 421円
    • 410円
    • 696円
    • 210円
    • 992円
    • 1,583円
    • 567円
    • 2,745円
    • 527円
    • 1,214円
    • 316円
    • 1,900円
    • 1,477円
    • 1,161円
    • 210円
    • 1,055円
    • 1,900円
    • 738円