お客様レビュー

レビューを書きます。
  • すべてのレビュー (256)
  • 画像 (28)
  • ビデオ (0)
  • オールスター
    • オールスター(256)
    • 5スター(244)
    • 4スター(10)
    • 3スター(1)
    • 2スター(0)
    • 1スター(1)
並び替え:
トップレビュー
  • トップレビュー
  • 最も役立つ
  • 新着商品
あなたの国からのレビューのみ(Japan)
|
オリジナルを表示

レビューの一部は自動翻訳されています。

  • 25/07/2020

    説明として製品。 正常に動作していることを確認しました。 モジュール金属カバーが鋭利な物体によって明らかに変形していることに気付いた時、少し感情的なショックを受けました。 幸いなことに、モジュールの古い画面は壊れませんでした。 最近、この売り手からの多くの注文は輸送中の保護の観点から非常に貧弱です。 紙の封筒の内側と大きなプラスチック封筒の内側のみ帯電防止袋。 内部の壊れやすいアイテムを保護するための気泡箔はありません。 古い lcd とこれらは、輸送中の粗いハンドリングによって容易に損傷する可能性があります。 短期的には、この手順は売り手のためのお金を節約することができますが、長期的には顧客は到着製品の死率が高いためにこの売り手から購入することを避けるため、それは罠です。 良い品質のボード。 推奨します。

    コメント
    オリジナルを表示
  • 12/05/2018

    it has a revision 1 chip it only has space for unprotected 18650 batteries

    コメント
    オリジナルを表示
  • 16/01/2018

    After a long search I finally had all the information to create my own sketches. So far, everything works. The OLED display is glued to the board. The adhesive dissolves after a short time. Doesn't look good, but it's harmless. Also a warning to everyone: The USB plug is soldered without through-plating and detaches relatively easily from the board. I am not the first to whom this happens. With my first board it happened already with the third plugging in. It's a case for e-waste. The connector goes very tight and is barely able to cope with the forces. This is now my second board and I will take appropriate precautions to prevent this from happening again.

    コメント (1)
    オリジナルを表示
  • 26/10/2019

    The unit is tidy, but perhaps a little larger than I was expecting, the measurements on pictures are accurate though. I took note of previous comments and have applied a couple of drops of superglue to the USB connector to stop it snapping off. I have used a 4x18650 battery pack which should allow this to run for ages, so far I have only run the demo The OLED display looks white, but shows up blue in the photograph. Be aware that the standard 0,1" DuPont style headers supplied with the unit will NOT connect to a breadboard if soldered to the underside because of the depth of the battery holder - you would to use female to male extenders - you could always solder them to the top, but you wouldn't see the OLED I intend to use this without the headers, so it doesn't make any difference to me

    コメント
    オリジナルを表示
  • 11/09/2019

    board is working and looking great

    コメント
    オリジナルを表示
  • 09/11/2019

    Good product. Recommended.

    コメント
    オリジナルを表示
  • 10/12/2021

    回転LED時計のモジュールを手に入れました。 POV画面。 このモジュールにはWIFIが含まれているので、彼はインターネットから時計を更新し、私は夏と冬の間に調整する必要はありません。 そして、私は時間を修正する必要はありません。 モジュール上のバッテリ用です。

    コメント
    オリジナルを表示
  • 07/04/2020

    公式のリリーゴ製品ではなく、公式の回路図に基づいて(ttgoのロゴが付いていない)、それは魅力のようである。 これは古いモデルです。 新しいモデルはlilygo ttgo t18と呼ばれます。 ソフトウェアと例は、GitHub と簡単な Google の研究に基づいています。 (次のキーワード: ttgo old とバッテリホルダー) 英国から出荷されるため、強くお勧めします。 ケーブルが接続されている場合、バッテリの重量が落下し、USBコネクタにブレーキがかかることに注意してください

    コメント
    オリジナルを表示
  • 05/10/2019

    la confezione non ha molte protezioni, ma non avendo i pin montati l'articolo non presenta danni. arriva con preinstallato uno scatck per il test del display. ho testato anche la batteria e funziona.

    コメント
    オリジナルを表示
  • 14/02/2019

    Very good ESP32 board. The built in OLED display is very easy to read. Bright enought. The Battery charger working fine. Recommended to buy together with a good 18650 battery.

    コメント
    オリジナルを表示
Show:

    合計 0 ページ

    ページに移動

    あなたにおすすめの商品

    recommendation for you
    • US$7.99
    • US$126.99
    • US$36.99
    • US$69.99
    • US$7.99
    • US$7.49
    • US$9.19
    • US$9.99
    • US$74.99
    • US$9.99
    • US$349.99
    • US$61.41
    • US$33.62
    • US$115.99
    • US$41.25
    • US$31.99
    • US$39.99
    • US$20.99