良い配達

Gute Lieferung

良い配達

価格と品質のバランスにおいて、最高のプリンターの一つだと思います。美しく印刷され、うまく動作しています！

Szerintem ár/érték arányban az egyik legjobb nyomtató,szépen nyomtat,jól működik! I think it is one of the best printers for the price/value ratio, it prints beautifully and works well!

価格と品質のバランスにおいて、最高のプリンターの一つだと思います。美しく印刷され、うまく動作しています！

とてもよく

muy bien

とてもよく

The bad: The instructions ask you to adjust the Y axis wheels using the eccentric nuts on the right side, but even after adjustment, only two of the wheels even rotate and the bed basically rests on the sides of the wheels rather than being properly slotted. I can lift the bed up slightly. The printer still prints fine, but it does bother me a bit and I wonder if it's a design fault or unique to my printer. The fans are very noisy, so this is not a quiet printer. I think there's hope that the fan bearings will eventually make less noise. The good: The prints look great and I'm printing much faster than I ever did on the SW X1. The bed heats up a lot slower, but I think I feel safer with the 36V DC bed compared to the 220V AC bed on the X1. There are tons of little improvements over the X1. The printer has the exact same footprint and I didn't have to make too many changes to my slicer settings, so it was an easy upgrade for me. Minor quibble: the file picker UI shows files that start with . and because I slice on a Mac, each gcode file has another file with the same name, except prefixed with ._ and those clutter up the files list quite a bit. The X1 doesn't have this problem.

The bad: The instructions ask you to adjust the Y axis wheels using the eccentric nuts on the right side, but even after adjustment, only two of the wheels even rotate and the bed basically rests on the sides of the wheels rather than being properly slotted. I can lift the bed up slightly. The printer still prints fine, but it does bother me a bit and I wonder if it's a design fault or unique to my printer. The fans are very noisy, so this is not a quiet printer. I think there's hope that the fan bearings will eventually make less noise. The good: The prints look great and I'm printing much faster than I ever did on the SW X1. The bed heats up a lot slower, but I think I feel safer with the 36V DC bed compared to the 220V AC bed on the X1. There are tons of little improvements over the X1. The printer has the exact same footprint and I didn't have to make too many changes to my slicer settings, so it was an easy upgrade for me. Minor quibble: the file picker UI shows files that start with . and because I slice on a Mac, each gcode file has another file with the same name, except prefixed with ._ and those clutter up the files list quite a bit. The X1 doesn't have this problem.

The bad: The instructions ask you to adjust the Y axis wheels using the eccentric nuts on the right side, but even after adjustment, only two of the wheels even rotate and the bed basically rests on the sides of the wheels rather than being properly slotted. I can lift the bed up slightly. The printer still prints fine, but it does bother me a bit and I wonder if it's a design fault or unique to my printer. The fans are very noisy, so this is not a quiet printer. I think there's hope that the fan bearings will eventually make less noise. The good: The prints look great and I'm printing much faster than I ever did on the SW X1. The bed heats up a lot slower, but I think I feel safer with the 36V DC bed compared to the 220V AC bed on the X1. There are tons of little improvements over the X1. The printer has the exact same footprint and I didn't have to make too many changes to my slicer settings, so it was an easy upgrade for me. Minor quibble: the file picker UI shows files that start with . and because I slice on a Mac, each gcode file has another file with the same name, except prefixed with ._ and those clutter up the files list quite a bit. The X1 doesn't have this problem.

今まで非常に良い！おすすめです！

Eddig nagyon jó! Csak ajánlani tudom!

今まで非常に良い！おすすめです！

きちんと梱包されていて良い買い物です。ただし、壊れたデータテープホルダーや曲がったピンがある不良コネクタについてはクレームを言わなければなりません。すべてをテストした後に新しいレビューをアップロードします。

Bien empaquetado y buena compra. Pero tendré que reclamar por un soporte de cinta de datos que viene roto y un conector con las patillas también defectuosas. Cuando tenga todo probado subiré nueva reseña.

きちんと梱包されていて良い買い物です。ただし、壊れたデータテープホルダーや曲がったピンがある不良コネクタについてはクレームを言わなければなりません。すべてをテストした後に新しいレビューをアップロードします。

大型オブジェクトを300x300x400まで印刷するための高性能3Dプリンター。前のモデルと比較して、同じブランドの自動レベリングベッドプロセスが含まれています。優れたプリンターの特別価格。迅速な配送と完璧な包装。

Stampante 3D ad alte prestazioni per stampare oggetti di grandi dimensioni 300x300x400. Tra gli altri miglioramenti rispetto ai precedenti modelli della stessa marca c'è il processo di autolivellamento del letto. Ottima stampante ad un prezzo straordinario.Spedizione veloce e imballaggio perfetto

大型オブジェクトを300x300x400まで印刷するための高性能3Dプリンター。前のモデルと比較して、同じブランドの自動レベリングベッドプロセスが含まれています。優れたプリンターの特別価格。迅速な配送と完璧な包装。

ottimo👌

ottimo👌

ottimo👌

迅速で手間のかからない配達。優れたサービス

Livraison rapide sans soucis. Excellente prestation

迅速で手間のかからない配達。優れたサービス

良い機械とトラブルフリーな輸送

buena maquina y trasporte sin problemas

良い機械とトラブルフリーな輸送