全面的なすばらしいサービスおよび良質品、，

overall great service and quality products,

全面的なすばらしいサービスおよび良質品、，

The IP2312 is efficient. Input output tested. This Board is highly recommended for replacing TP 4056.

The IP2312 is efficient. Input output tested. This Board is highly recommended for replacing TP 4056.

The IP2312 is efficient. Input output tested. This Board is highly recommended for replacing TP 4056.

私はまだ試していませんが、写真と同じです

henüz denemedim resimdekinin aynısı

私はまだ試していませんが、写真と同じです

全て良い

all good

全て良い

hat bestens funktioniert

hat bestens funktioniert

hat bestens funktioniert

うまく動作しません

Does not work well

うまく動作しません

問題なし

no problems

問題なし

非常に優れたパワーバンクモジュール。 2Aの入出力はなかなか得られませんでしたが、1.8Aは大丈夫でした。

Sehr gutes Powerbank-Modul. Die 2A In- und Output konnte ich nicht ganz erreichen, aber 1,8A waren okay.

非常に優れたパワーバンクモジュール。 2Aの入出力はなかなか得られませんでしたが、1.8Aは大丈夫でした。

テスト済み、それは良いです。

Tested, it's good.

テスト済み、それは良いです。

Does NOT WORK, DO NOT BUY! I hooked it up to 6 Lithium cells and tested it out. Discharging the cells was only possible at around 200-300mA. Swapping my phone out for another one, thinking it might be an issue with my phone, did not help either. Even hooking it up to an 1 Ohm Resistor and also with a 2.5 Ohm Resistor only resulted in 450mA current for a second, after which the BMS shut down and dropped to the current to 0mA. Charging on the other hand was possible, but only with a continuous current of around 500mA, despite having a reliable 2A charger. (Note that on the last image I was using the data hold function of my multimeter and the black probe is not touching the contact inside the usb cable when I was taking the picture. This is due to a lack of multiple hands, as taking the picture and measuring was not possible at the same time ;))

Does NOT WORK, DO NOT BUY! I hooked it up to 6 Lithium cells and tested it out. Discharging the cells was only possible at around 200-300mA. Swapping my phone out for another one, thinking it might be an issue with my phone, did not help either. Even hooking it up to an 1 Ohm Resistor and also with a 2.5 Ohm Resistor only resulted in 450mA current for a second, after which the BMS shut down and dropped to the current to 0mA. Charging on the other hand was possible, but only with a continuous current of around 500mA, despite having a reliable 2A charger. (Note that on the last image I was using the data hold function of my multimeter and the black probe is not touching the contact inside the usb cable when I was taking the picture. This is due to a lack of multiple hands, as taking the picture and measuring was not possible at the same time ;))

Does NOT WORK, DO NOT BUY! I hooked it up to 6 Lithium cells and tested it out. Discharging the cells was only possible at around 200-300mA. Swapping my phone out for another one, thinking it might be an issue with my phone, did not help either. Even hooking it up to an 1 Ohm Resistor and also with a 2.5 Ohm Resistor only resulted in 450mA current for a second, after which the BMS shut down and dropped to the current to 0mA. Charging on the other hand was possible, but only with a continuous current of around 500mA, despite having a reliable 2A charger. (Note that on the last image I was using the data hold function of my multimeter and the black probe is not touching the contact inside the usb cable when I was taking the picture. This is due to a lack of multiple hands, as taking the picture and measuring was not possible at the same time ;))