お客様レビュー

レビューを書きます。
  • すべてのレビュー (435)
  • 画像 (68)
  • ビデオ (0)
  • オールスター
    • オールスター(435)
    • 5スター(427)
    • 4スター(7)
    • 3スター(1)
    • 2スター(0)
    • 1スター(0)
並び替え:
トップレビュー
  • トップレビュー
  • 最も役立つ
  • 新着商品
あなたの国からのレビューのみ(Japan)
|
オリジナルを表示

レビューの一部は自動翻訳されています。

  • 08/05/2017

    A propeller cut one of the antennas on my RX, so needed replacements. Price is low and quality looks OK, have not tried them yet. The unshielded part of the antenna is not protected by an extra plastic tube like on the original antennas on my RX, but should not be a problem.

    コメント
    オリジナルを表示
  • 11/07/2018

    Not ipex or pigtail you must be solder directly receiver.

    コメント
    オリジナルを表示
  • 04/01/2018

    These are great antennas they'll restore your RX to full range after you put the original ones into your props. Very challenging to solder though my picture is magnified 50x and the joins are good... You'll need a bloody small soldering tip and a couple of drinks to steady your hand and you'll be good to go! I think I'll get receivers with the plug type connectors from now on.

    コメント
    オリジナルを表示
  • 29/07/2021

    良好な交換 2.4 GHz レシーバアンテナ。 兵士が 出て行く 買おう。

    コメント
    オリジナルを表示
  • 07/08/2017

    Elle m'ont servit a remplacer les antennes de mon récepteur XSR. Elles sont un peu plus longues mais ça n'est pas dérangeant et elles sont surtout super faciles à souder. Aucun soucis avec. :-)

    コメント
    オリジナルを表示
  • 26/02/2018

    I used these to repair some damaged antennas on my Turnigy receivers. Worked just as well as the originals. recommended.

    コメント
    オリジナルを表示
  • 17/04/2018

    Just what I was looking for. These are the shielded antenna wires but instead of the more expensive braided shielding, this is the cheaper foil shielded antenna replacement. It DOES NOT have and plug on the end (like FrSky uses) instead I soldered the center cable to the existing antenna location, then grounded the shielding to any ground point on the PCB (used cont. tester to locate a ground point) When soldering the foil, use a dab of flux, tin the surface first, and only touch the tip of iron a brief time to avoid melting the plastic tubing. Worked just as I wanted to extend the working portion of the antenna past carbon fiber frame.

    コメント
    オリジナルを表示
  • 23/06/2017

    Это очень хороший вариант! Дёшево!

    コメント
    オリジナルを表示
  • 26/04/2017

    got these for the XSR, will see how they fair in longer range tests but seem good!

    コメント (1)
    オリジナルを表示
  • 22/04/2017

    GOOD

    コメント
    オリジナルを表示
Show:

    合計 0 ページ

    ページに移動

    あなたにおすすめの商品

    recommendation for you
    • US$109.99
    • US$19.99
    • US$53.99
    • US$67.99
    • US$25.99
    • US$10.99
    • US$12.99
    • US$22.99
    • US$13.99
    • US$2.99
    • US$11.99
    • US$10.99
    • US$23.99
    • US$31.99
    • US$10.99
    • US$18.99
    • US$239.99
    • US$7.99